Question about 1987 Yamaha FZR 1000

1 Answer

When the stater button is pressed the engine does not turn over the oil light comes on but there is no neutral light everything else works lights horn ect. all fuses are good

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 42 Answers

Looks like you have a switch on your left handlebar that might cut power if you don't pull the clutch in. I've seen a few that have failed. Try wiring them together (to create a circuit) and see if it will let you do that. But if you don't have a neutral light on....you had better make sure the bike IS in Neutral first. Or at least throw the back on a stand so its up in the air, otherwise the bike may lurch forward and fall. Also, check the battery, sometimes they have enough juice to turn the lights on/horn etc, but not enough to start the motor. Good luck.

Bruno

Posted on Nov 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn buttons works the radio


Suspect a short circuit in the steering column wiring

Jun 20, 2016 | Cars & Trucks

Tip

Wiring Diagram Kawasaki GPZ 750


Kawasaki GPZ750 (ZX750) Turbo North American models.<br /><br /><img src="suzman_10.JPG" /><br /><br />1 - Right turn <br />2 - High beam<br />3 - Warning light<br />4 - Headlight fail<br />5 - Neutral<br />6 - Left turn<br />7 - Boost Guage <br />8 - Tach light<br />9 - Tach/volt switch<br />10 + 11 - Speedo lights<br />12 + 13 - Illum. lights<br />14 - Spare connectors<br />15 - LCD + warnig lights<br />15 + 16 - LCD illum<br />17 - RF indicator<br />18 - Horns<br />19 - Headlamp<br />21 - LF indicator<br />22 - Reserve lighting unit<br />23 - Hazard switch<br />24 - Indicator switch<br />25 - Horn switch<br />26 - Dimmer switch<br />27 - Starter lockout switch<br />28 - Neutral switch<br />29 - Side stand switch<br />31 - Oil pressure switch<br />32 - Alternator<br />33 - Regulator<br />34 - Solenoid<br />35 - Starter<br />36 - Battery<br />37 - Junction box<br />38 - LR Indicator<br />39 - Stop/tail lamps<br />40 - Stop/tail lamps<br />41 - RR Indicator<br />42 - Injectors<br />43 - Engine temp switch<br />44 - Boost sensor<br />45 - Fuel pump<br />46 - Air temp sensor<br />47 - Throttle sensor<br />48 - Main pump relay<br />49 - Fuel injection control unit<br />50 - Rear brake switch<br />51 - Pick-up coils<br />52 - Ignition control unit<br />53 - Coils<br />54 - Spark plugs<br />55 - Fuel level sensor<br />56 - Front brake switch<br />57 - Starter/engine stop<br />58 - Ignition<br />

on Nov 22, 2010 | Motorcycles

Tip

1972 Chevrolet Nova wiring


This is the wiring diagram for a 72 Chevy Nova. Everything that's needed to get the engine electrical up and running.<br />Eng. is the engine bay wiring.<br />B - battery<br />S - starter<br />C - coil<br />D - distributor<br />R - regulator<br />A - Alternator<br />H - horn relay<br />T - temperature switch<br />O - oil pressure switch<br /><img src="suzman_4.JPG" /><br /><br />Int. is the interior wiring for the engine.<br />Ign. - Ignition<br />N - Clutch/Neutral safety switch<br />T - Temperature guage<br />O - Oil light<br />C - Charge light<br /><br /><img src="suzman_5.JPG" /><br />

on Nov 17, 2010 | Chevrolet Nova Cars & Trucks

1 Answer

Bike wont start, turn the key n everything lights up as normal, press the start button n just nothing


It could be the link from the starter button to the ignition coil. If you can check this for a current it should give an indication of the problem.

Jul 11, 2015 | 2005 Yamaha XVS 1100 Dragstar

Tip

Chevrolet service light 1991-01


Camaro

1998-01

To reset the "OIL CHANGE" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset.


Corvette


1997-01

To reset the monitor after an oil change, turn the ignition on. Press the "TRIP" button so that the "OIL LIFE" percentage is displayed. Press "RESET" and hold it for two seconds. The word "RESET" should appear on the monitor, then "OIL LIFE 90%".


Impala,
Monte Carlo


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator three times within five seconds. If the CHG OIL SOON lights two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not been reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to exit programming. A chime will be heard to verify the exit.


Impala,
Caprice


1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Lumina,
Monte Carlo,
Impala,
Caprice


1996-00,
1996-99,
1995-96,
1995-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. The light will flash and go out.


Corvette


1990-96

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.


Chevrolet Suburban,
GMC Yukon XL,
Chevrolet Silverado,
GMC Trucks Sierra


2000-01,
1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.


Silverado, Sierra Trucks


1991-93

To reset the "CHANGE ENGINE OIL" message, turn the ignition key to the run position. Press and release the accelerator pedal three times within 5 seconds. If the light flashes for 5 seconds, the system is reset. Repeat procedure as needed.















on Dec 07, 2009 | Chevrolet Camaro Cars & Trucks

Tip

Cadillac service light 1989-01


Eldorado

2000-01

Turn the ignition to ON. Press the TRIP button on the driver information center (DIC) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIC switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.


DeVille,
Eldorado


1999

To reset the service Oil Life Indicator, display the
"OIL LIFE LEFT" message by pressing the "INFORMATION SKIP" (skip info) button. Press and hold the "RESET NO" (no info reset) button until "100% OIL LIFE" is displayed.


Deville,
Seville


2000-01

Turn the ignition to ON, Press the INFO button on the driver information center (DIC) to display ENGINE OIL LIFE. Press and hold the INFO RESET button on the DIC until the display reads 100% ENGINE OIL LIFE. The engine oil life index is now reset. Turn the ignition OFF.


Deville,
Seville,
Eldorado


1997-98

Display "ENGINE OIL LIFE" by pressing the "INFO" button. Press and hold the "INFO RESET" button until the message shows 100.


All Models
except
Fleetwood


1994-97

Press the "INFORMATION" button until "OIL LIFE LEFT" is displayed. Press the "RESET" button until "100" or "0.0 OIL LIFE LEFT" is displayed.


Fleetwood


1994-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds.


All Models,
Seville,
Eldorado


1993,
1994-95,
1994-95

The automatic transaxle message can be reset through the following procedure. If "CHANGE TRANSAXLE FLUID" appears on the Information Center, press and hold the "OFF" and "REAR DEFROST" buttons until "TRANS FLUID RESET" appears.


DeVille,
Fleetwood


1991-93

When "CHANGE OIL SOON" light is illuminated, press and hold the "RESET" and "RANGE" buttons on the Fuel Data Center for 5 to 60 seconds. When the buttons are released, the light will flash four times if it has been reset. If the light comes back on for more than 5 seconds, repeat the procedure.


Allante


1989-93

When "CHANGE OIL SOON" appears on the Driver Information Center, press the "RANGE" button until "OIL LIFE INDEX" shows on display. Then press and hold "AVG SPEED" and "RESET" (or "RANGE" on late models) buttons until display shows "100".


Seville,
Eldorado


1992-93

Press "INFORMATION" button on the Driver Information Center until "OIL LIFE INDEX" is displayed. Press "STORE/RECALL" until "OIL LIFE INDEX" resets to 100.


Seville,
Eldorado


1989-91

When "CHANGE OIL SOON" or "CHANGE ENGINE OIL SOON" appears on the Driver Information Center, press "ENG-DATA" button until the "OIL LIFE INDEX" appears. Then press the "ENG-DATA" button and the "RANGE" buttons at the same time until 100 displays (about 5 seconds).





















on Dec 07, 2009 | Cadillac Eldorado Cars & Trucks

1 Answer

97 sportster the odometer light came on and nothing else, no oil light, neutral light, head light and it didn't do anything when I hit the starter button. But the horn worked fine normal loudness


Hi Dolphnl, and the usual suspects are:
1.Ignition/Light Key Switch not in IGNITION position.
2.Engine Stop switch in the OFF position.
3.Discharged battery, loose or corroded connections check negative cable at both ends. (solenoid chatters).
4. Bank Angle Sensor tripped and Ignition/Light Key Switch not cycled to Off and then back to on.
5. Starter control circuit, relay or solenoid faulty.
6. Electric starter shaft pinion gear not engaging or over-running clutch slipping.
7. Security alarm not disarming
Good luck

Oct 17, 2012 | Harley Davidson XL Sportster 883...

1 Answer

2006 jeep liberty dying randomly. Oil change and new air filter. About to change spark plugs and wires. No gauge lights, no sputtering. Just turns off randomly, starts right back up when I put in neutral...


My 2006 Liberty has a similar issue. The oil light beeps and then the engine shuts off. I put the car in park and it restarts and the oil light goes off. I had the oil, filter, and lines checked and everything checked out. The mechanic thinks it may be the oil sensor going out and that for safety reasons the engine shuts down when the oil light comes on.

Jul 12, 2012 | Cars & Trucks

2 Answers

How do i reset the oil change light in a 2003 olds alero


turn key on (dont start engine) floor gas pedal 3 times 1,2,3. turn key off, now start engine it should go off, if not try it again.

Aug 03, 2011 | 2003 Oldsmobile Alero

Not finding what you are looking for?
1987 Yamaha FZR 1000 Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...