Question about Husqvarna SM 125 S Motorcycles

Open Question

Have error ecu 2 Husqvarna sm125s 2007 A previous owner tried to perfect a motor cycle and set a basic jet 170, probably and bored ductings in a carburetter. It is possible as that is related to the error. I in same queue increased idling to 45 (that is why from a difference between the sizes of jets a motor cycle did not work on single), and decreased to basic 140.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: I have a 2004 volusia with vance and hines exhaust

It all depends which way you need to go on the jetting for best performance. A richer mix will burn more gas and a leaner mix will burn less. Either way, you will not see a major difference in mpg.

Posted on Jun 25, 2009

stephensaon_
  • 284 Answers

SOURCE: How to remove idle jet?

The idle jet is located in the bottom of the car. it's the recessed one in the bottom of the body. Remove your air cleaner assembly. remove the four screws. Be careful because it will be full of gas. ( well vented area.) You'll have one jet sticking out. That's your main. right next to it is a recessed jet . That is your idle. you'll have to use a small flathead screw driver to get it out. Make sure you have god pressure on the jet to break it loose. The jet itself is brass, and you don't want to mess it up. You should probably have a 45 jet with your combo. if you've been messing with the mixture screw it should be set around 1 & 1/2 turns out from lightly seated.

Posted on Jun 27, 2009

wd4ity
  • 4565 Answers

SOURCE: Had a 1200 upgrade, new exhaust valves, guides

I would say that something has changed since you had the work done. You said that it ran good and got 54 mpg (you said "mph" but I think you meant MPG") after the work was done. Now, it's backfireing, sputtering, and getting 37 mpg with dry black deposits on the plugs. Something has changed.

Considering that you didn't mention anything you changed, the only thing that has changed is the weather, it has turned cold. Cold air is more dense than hot air therefore, your carb should be running leaner, not richer. But, I'd be willing to bet that you're allowing your bike to run longer with the enricher on when warming it up before a ride. Am I right?

The enricher circuit is a very rich mixture. It's rich enough that if you allow your engine to run too long with the enricher on, it will foul your plugs. Fouled plugs are indicated by a black sooty deposit on them. In my experience, once a Sportster fouls a plug, it will not clean itself like a Big Twin will. Why this is I have no idea but that's my experience. You'll either have to replace the plugs or get them cleaned somewhere. I clean them in a glass beading machine but you have to blow them out very well before reinstalling them. I also put a little anti-seize on the threads to keep from damaging the spark plug hole threads.

Try installing a new set of plugs and when you start your bike, only run the enricher long enough to warm the bike to the point where you can keep it running with the throttle lock knob to bring the engine to operating temperature. That enricher is a plug killer.

The only other thing I can figure is that the main jet has come loose and fallen out, trash in the needle and seat, a vacuum leak on the front head at the intake manifold, the VOES, or petcock. If it ran good in warm weather with the 170 main, it should run good or may a tad lean in cold weather.

Posted on Dec 30, 2009

  • 76 Answers

SOURCE: looking for factory jet sizes for a wr250 2006

slow jet #40
mainjet #95
medium jet #72

Posted on Jan 31, 2010

  • 382 Answers

SOURCE: We put a jet kit from dynojet for a 2007 suzuki

Sounds like its running too lean, you need to jet it richer or else you risk damaging the motor. Jetting is a painful tuning process and had to be done each time any change is made to the exhaust or intake.

When you run rich you loose power and create more smoke, when you run lean you are more efficient, slightly more power but runs too hot and causes damage.

Cheers,

Kevin

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problems starting husqvarna 6.25 awd walk behind mower


Hi it's probably a Briggs & Stratton motor good motors first of try a new spark plug if this doesn't work give the carby a good clean blow out all the jets inside .,.good luck

Apr 05, 2016 | Husqvarna Garden

1 Answer

Have replaced solenoid battery starter motor on my lth1742 husquana but still will not turn over help


Pull out the spark plug and try to turn over by hand. If you can then it is probably your starter is weak. If you cannot then you may have internal damage

Sep 02, 2013 | husqvarna"" ls 2 cycle oil"

1 Answer

I m facing problem hp laserjet 3005n 59.50 error


59.50 ERROR

alternates with

To continue turn off then on

A main motor (M1) error has occurred. Motor

operation is verified during device power-up.

1. Turn the device off and then on.

2. Verify that nothing is hindering the main

motor. If necessary, remove all paper

trays and the print cartridge, and then

turn on the device and listen for motor

operation.

3. Verify that the main motor is connected

to connector J407 on the ECU. (See

Figure 6-9 ECU wiring on page 195.)

You might have to remove the main

cooling fan to see this connection.

4. If the message persists, replace the
motor.

Part #
RK2-1488 Main Motor

Dec 31, 2010 | Laser Jet P3005d Printer

1 Answer

I have a 1987 Kawasaki js550 Jet Ski with low compression. it has 170 in the front piston and 50 in the back what could be done besides having a stuck piston ring?


You will have to pull the engine out and rebuild the top end. You will probably have to bore the cylinders. Purchase a piston kit that comes with gaskets and seals. Reseal the crankshaft with the new seals and your motor should be good for another 23 years.

Oct 22, 2010 | Encore Software Kawasaki Jet Ski...

1 Answer

Jet bore threads not holding properly,side covers,breaking system


The jet bores are supposed to have a plastic liner near the outside of the bores that grips the jet screws to hold adjustment. You could try inserting a piece or two of thin plastic fishing leader, then inserting the jet screw. Don't insert so much leader that the material gets into the pointed end of the screw area as it will plug the jet. Any other threads that are not holding after being properly tightened can be be restrained by applying 'Loc Tite' thread locker fluid (from an auto parts house) to the threads before putting things together. Does the machine seem to have excessive vibration? Investigate the problem if it does. Hope this helps!

Apr 26, 2010 | Husqvarna Chain Saw 20" Bar

1 Answer

What is the gas oil ratio for the Husqvarna 130BT


The ratio is 50:1. Use a good quality 2 cycle oil for mowers and equipment, not for boat motors. You can probably buy a bottle for the 50:1 ratio with just the right amount of oil. Look for a bottle with 2.6 oz. That is the correct one. You can use either regular oil or synthetic oil.

If you need an owners manual, go to Husqvarna.com and look for the homeowners manuals. Search for yours with a space between the 130 and BT( 130 BT )


Oct 23, 2009 | Husqvarna Garden

1 Answer

Need carb settings for a Husqvarna wr125 1999 model


Main Jet 400
Jet Needle 6DJ8-60
Jet Needle Groove - 3rd
Pilot Jet - 35
Idle air screw - 1+1/2
Slide 3.0

Free manual here... http://safemanuals.com/user-guide-instructions-owner-manual/HUSQVARNA/WR%20125-_M

Aug 04, 2009 | 2000 Husqvarna WR 125

1 Answer

Husqvarna 324LDx 4 cycle string trimmer. Have


Probably needs a carb kit, check main jet and main fuel inlet jet, is the spark crisp, fat and powerful, try running it with a borrowed coil as this may have an intermittent fault. Is fuel cap breather working or blocked, these small carbs are very sensitive. Make sure all is well with gaskets and diagrahms. Good luck the Yeti

May 17, 2009 | Husqvarna 28cc Gas Line Trimmer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...