Question about 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

No electrics when turn the on switch. - 2001 Harley Davidson FXDL Dyna Low Rider

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

First, check the battery, Take it to an automotive parts house and ask them to "load test" the battery. They'll usually do this free. Then check all the connections and make sure they are clean and tight. Follow the red wire, not the large battery cable, to the main fuse or breaker and make sure the fuse is not blown or the breaker tripped.

Good Luck
steve

Posted on Oct 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Break lights and hazord lights on 1997 blazer don’t work


Do you know what a wiring diagram is ? How to test automotive electrical circuits using a digital voltmeter ? This is how professional auto technicians find electrical faults .
Electric Testing Techniques You Need to Know
The Trainer 73 Building Solid Electrical Foundation
The voltage is supplied at all times through the STOP HAZ Fuse 1 to the TCC brake and cruise control release switch. The contacts in the TCC brake and cruise control release switch close when the brake pedal is depressed. The voltage is supplied through the hazard switch and the turn signal switch to the left and right stoplamps. The stoplamp will flash as a turn signal lamp if the turn signal switch is on. The stoplamp on the opposite side will serve as a stoplamp.

Sep 19, 2018 | Cars & Trucks

1 Answer

How do I turn my hot water heater on from gas to electric in my flag staff camper


if has electric feature if suburban check outside lower left for switch to activate electric then turn on switch inside and turn off LP switch

Jun 13, 2018 | Water Water Heaters

1 Answer

My 87 doge died we worked on it now the key wont work to start it has had problems befor when you turn it off it dont want to go off it sputters and sometime i have to turn the key back on then off just to...


All sign is pointing to a bad electric switch.
The ignition switch is consist of three parts.
1)key way 2)steering lock 3)electrical system
In your case,it can be a bad switch and/or worn linkage point where they connect.
As you turn the key,there is a shaft/linkage (just like a screw driver) that turn the electrical switch,
Over time the plastic center will worn down or crack.


Depend on your skill level you can pass a vacuum over the hosing to clean to as far as replacing the electrical switch.
This is a very inexpensive $15 part. ~1 hour of labor time.
mustgo_74.jpg

Aug 10, 2011 | 1987 Dodge Dakota

1 Answer

I have a minkaie switch model uc9040t, I went to turn the light on, on the fan and it blew the light and now when I look at the switch on th on position the green light is off like there is not electricity...


I have a minkaie switch model uc9040t, I look at the switch on the on position the green light is off like there is not electricity coming to the switch, but itested the cables and there is electricity, and of course the fan won't turn on either, is there a way to reset this switch

Jan 31, 2011 | Minka Aire Ceiling Fan

1 Answer

Replaced the bulbs and checked fuse but the brakelights fail to work. Could it be a switch.


Yes, it could be the switch behind your brake pedal.

  1. Remove the driver's side instrument panel trim panel/sound insulator.
  2. Detach the switch electrical connector.
  3. Remove the switch from the retainer by grasping it, turning the switch 90° counterclockwise, and pulling it toward the rear of the car.

082d67c.gif
The brake light switch (3) is mounted on the brake pedal support (1) and secured with a retainer (2)

To install:
  1. Insert the brake light switch into the retainer until the switch body seats on the retainer.
  2. Pull the brake pedal upward against the internal pedal stop.
  3. Turn the switch 90° clockwise in order to lock it into position.

NOTE Proper switch adjustment is achieved when no clicks are heard as the pedal is pulled upward and when the brake lights do not stay on without brake application.


  1. Attach the switch electrical connector and test the switch for proper adjustment.
  2. Adjust the brake light switch, as follows:
    1. Detach the switch electrical connector.
    2. Remove the switch from the retainer by turning it counterclockwise 45°, and pulling it toward the rear of the car.
    3. Insert the switch into the retainer until the switch bottoms out against the brake pedal and the switch actuator button is fully depressed.
    4. Snap the switch into the retainer by turning it clockwise 45° until a click is heard.
  3. Attach the switch electrical connector.
  4. Install the hush panel/sound insulator.
  5. Connect the negative battery cable.

Sep 13, 2010 | 1998 Oldsmobile Cutlass

1 Answer

I have a Whirlpool Gold electric cooktop. It is


It sounds like the selector switch is shorted, the only way to fix that is to replace the switch

always unplug electricity before working on any electrical appliance

Sep 25, 2017 | Whirlpool GJC3034 Electric Cooktop

1 Answer

Dashboard lights burning out, down to 1 illuminating tach, speedo, gas gauge. How complicated to replace?


one hour job. find bulb part number in bulb chart in owner manual.

go here for villager help.

http://groups.yahoo.com/group/villagerquest/

Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
-------------------------------------------------------------------------------------------------
Instrument Cluster
Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
  1. Remove the four instrument cluster screws.
  2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).

Jan 13, 2010 | 1995 Mercury Villager

1 Answer

"Double" electrical switch has failed to function


In a standard 3-way switch arrangement you can turn the light on or off from each position.  If the wall switch has failed then only the bed switch will turn the light on/off.  Replace the wall switch with a new 3-way switch.

Jun 02, 2009 | Hubbell Electrical Products 2 Gang PVC...

Not finding what you are looking for?
2001 Harley Davidson FXDL Dyna Low Rider Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5948 Answers

Mike

Level 3 Expert

4363 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...