Question about 2000 Harley Davidson FLHR-FLHRI Road king
Hi Opacheco1, 4 out of 5 Harley Gods give this one a thumbs up, but just to be on the safe side contact your local dealers service/parts department for confirmation. Good luck and have nice day.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Jun 21, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: fuel pump?
the fuel pump for your 2000 fuel injected road king is located in the fuel tank. you will have to remove the speedometer housing, by first removing the seat, then remove the one small screw near the seat that holds the speedometer housing in place, also remove the small screw at the front of the speedometer housing and lift the housing off the tank and disconnect the wiring that goes to the back of the speedometer. there is a large oval shaped gold in appearance plate on top of the fuel tank. this plate is what the fuel pump is mounted to.
Posted on Mar 31, 2009
Sounds like the intake manifold is leaking. The area where the leak usually happens, are those two rubber sleeves that go from the heads, (Cylinder heads) to the intake. Sometimes the clamp/s loosen up. Sometimes these rubber sleeves deteriorate, and cracks form.
This makes the engine backfire, pop, and idle fast.
The added air at the wrong time cause a backfire, when you let off the throttle. The added air causes the engine to pop, because the exhaust valve has sucked up some cold air.
The engine idles fast, because more air is being introduced, and not metered by the injection system.
(The exhaust valve thing. Exhaust valves are supposed to open, and let exhaust out right? Well there is a thing called Valve Overlap.
The Exhaust valve hasn't closed all the way yet, and the Intake valve is opening.
The 4 stroke engine, (Of which a Harley is), has these four strokes.
1.Intake Stroke. Fuel/air is sucked in.
2.Compression Stroke. The piston comes up and squeezes the fuel/air mixture.
3.Combustion Stroke. The spark plug lights the fuel/air mixture off.
4.Exhaust Stroke. The spent gases are expelled out.
Your Road King has one camshaft. There are four cam lobes on it.
Intake, Exhaust, Intake, Exhaust.
If you had the camshaft in your hand, and had the gear end facing you, look down the camshaft. You will see those egg shaped cam lobes. You will notice that No.1 cylinder Intake lobe is facing to the left.
No.1 Exhaust is facing to the right.
If you put a degree wheel on the gear end of the camshaft, and had the No.1 Exhaust lobe ramp nose facing straight up, you would see that it's about 110 degrees, before the Intake lobe ramp at .050 lift, comes into play. (The roller, of your roller lifter has raised the Exhaust valve up .050 inch) There is about 55 degrees before the Exhaust valve hasn't quite shut.
This is okay for normal running. Introduce a vacuum leak, and the surge of extra cold air, makes it pop.
Solution? I suggest checking to see if the clamps on those rubber sleeves are loose. You can also spray WD-40 towards the ends of each rubber sleeve, when the engine is idling, and see if it speeds up. Means, one or more, of those rubber sleeves has deteriorated.
Posted on Apr 25, 2009
If you look at the top of the Induction module, you'll see if it is either black ( single looking tube ) or Silver ( Looks like 2 tubes together ) Single tube is Delphi, Silver Dual tube is Magnetti .
I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_5bac37c3cb991fdb
Posted on Jun 12, 2009
Not too hard - Undo the two bolts on the caliper and then seperate the caliper and pull the old ones out. Insert the new ones and put the bolts back in to hold the caliper back together and then install them back on the bike with the two retaining bolts. Use a bit of lock tight (Blue) on the threads. Warning do not let anyone apply pressure on the brakes while you have them off the bike or you will have a mess and/or a problem.
Posted on Jun 21, 2009
Thats not totally correct. remove your air filter cover. look to the lower right side. You will see a small hole thats where the screw driver goes in to adjust your idle. Ya the dealer has a scanlizer that can also do it if u want to spend the bucks.
Posted on Dec 20, 2009
Tips for a great answer:
Sep 27, 2015 | Motorcycles
Jul 11, 2014 | 2002 Harley Davidson FLHRCI Road King...
Apr 20, 2014 | 2003 Harley Davidson FLHR Road king
Dec 27, 2013 | 2003 Harley Davidson FLSTCI Heritage ...
Dec 26, 2013 | 2003 Harley Davidson FLHRCI Road King...
Mar 24, 2013 | 2005 Harley Davidson FLHRS - FLHRSI Road...
Aug 30, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king
Jun 05, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king
May 15, 2010 | Harley Davidson Harley-Davidson FLHR Road...
Sep 12, 2009 | 2002 Harley Davidson FLHRCI Road King...
240 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: