Question about 2004 Buell Blast
Hi, Miles9730 for more information about your issue and free downloads that you will need please visit the websites below, and for specific information or questions, please feel free to contact me at email@example.com. Good luck and have a nice day.
Buell Service Manuals PDF Download
TWIN Motorcycles Buell parts
2001 Buell Blast Owners Operators Owner Manual Factory 2001 eBay
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Jan 09, 2016
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
If you did not completely disassemble the carb and remove all jets/emulsion tubes/needle valves then you did not clean the carb adequately. You could try adding either Seafoam, the Yamaha CARB-CL-EAN-ER, or Techron fuel system cleaner in an auxiliary gas tank and running the engine for a short while to ensure the mix gets into all the nooks and crannies. Let it sit for a couple hours to do the work, then drain out the float bowl, hook up the bike's gas tank and see what happens. Otherwise you need to remove, strip, clean, reassemble, and reinstall the carb.
Posted on Feb 26, 2009
Hello chopper...glad to see a Buell owner, sorry to hear you are having problems. I have a 2000 Thunderbolt.
When you adjusted your clutch did you adjust it both places..one behind the rubber boot for cable adjustment and the other behind the primary cover?
Also check inside your primary and look for anything that might be rubbing where it shouldn't. New noises are often caused by a new occurence. Also look for metal shavings in your primary fluid and make sure it's full.
Good luck...hope this helps
Posted on May 23, 2009
ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Posted on Jun 27, 2009
Either fuel filter is clogged or air filter is clogged or carb/fuel injectors need to be thuroughly cleaned
Posted on Oct 12, 2009
Testimonial: "It ended up being the Carb needed a good cleaning. Thanks!! J"
Tips for a great answer:
Nov 17, 2013 | 2001 Buell Blast
Nov 17, 2013 | 2001 Buell Blast
Jun 27, 2012 | 2001 Buell Blast
Apr 09, 2012 | 2003 Buell Blast
Jul 10, 2011 | 2001 Buell Blast
May 29, 2011 | 2004 Buell Blast
Sep 26, 2010 | 2002 Buell Blast
Jul 17, 2009 | 2004 Buell Blast
Jun 26, 2009 | 2001 Buell Blast
Jul 19, 2018 | Motorcycles
111 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: