Question about 1996 kawasaki ZX-7RR

Open Question

I need the correct torque setting for a zx7r swing arm

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 68 Answers

SOURCE: how much torque need kawasaki zx 14 swing arm

About 40-50 ft pounds Chaz Moto DC

Posted on Jan 22, 2010

  • 152 Answers

SOURCE: how much torque need kawasaki zx 14 swing arm

Hi hope this helps.

Posted on Jun 05, 2014

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Changing a rear coil spring on a 05 echo

Jack up both sides of the rear of the car. LOWER ONTO AXLE STANDS. You will need the jack for another job.
Use the jack to GENTLY take the weight of the swing arm. (Marked A). Just enough to allow you to remove the bottom bolts through BOTH dampers, (Marked B). SLOWLY and GENTLY lower the jack and both springs, (marked C), should become loose enough to pull out.
ea95d7d4-1661-453b-a221-57b1993e0768-gdwjs3mziq0tgl1byg3c3jnn-3-0.jpeg Insert the springs and slowly jack up the swing arm (A) until it is nearly in position. Make sure the springs (C) are seated properly, then gently jack up the swing arm until you can re-insert the damper bolts, (B). Once they are the correct tightness, GENTLY lower the swing arm. Check the springs are in position and drop the swing arm all the way.
Raise the car and remove the axle stands.

Jan 23, 2018 | Cars & Trucks

1 Answer

Torque for 2005 dyna wide glide swing arm bolt

Hi, Bill for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at Good luck and have a wonderful day.
need torque spec for swing arm axle 07 dyna Harley Davidson Forums
Harley Davidson Dyna Glide Twin Cam 88 Service Manual
Instant Tech Relief To speak to me personally absolutely "FREE"

Jun 23, 2017 | 2005 Harley Davidson FXDWG - FXDWGI Dyna...

1 Answer

Loose swinging arm

Lay the bike on its side. Superglue the bush to the swing arm. Lay the bike over the other way and repeat. Do not glue the bush to the shaft.

Nov 27, 2014 | 2009 Harley Davidson FXDC Dyna Super Glide...

1 Answer

What is the proper way to use belt tensioner on a harley fxr

Not sure what you are asking but...

The belt tensioner gauge should be placed on the drive belt as close to its middle section as possible and pushed against the belt with a pressure of 10 pounds to see how far the belt deflects. You need to know the proper 10 lb pressure belt deflection for the particular year and model of bike. Once you know what the deflection should be if the belt is too tight loosen the axle cone nut and adjust the wheel forward to get the correct deflection and then tighten the cone nut to the correct torque for the model and year of the bike and retest the deflection to be sure it has remained the same throughout the cone nut tightening procedure. If the belt is too loose adjust the wheel more towards the rear of the bike and do as above for properly tightening the axle cone nut and recheck the deflection again as above. To maintain correct wheel alignment adjust each side of the wheel equally forward or backwards as the circumstances require. In case the alignment was not correct when you began OR to be certain that you adjusted each side equally measure the distance from the center of the swing arm attaching fasteners (or some other precise point on both sides of the swing arm - some swing arms have special measurement holes in the rear swing arm) to the middle of the axle. It should be the same measurement plus or minus 1/32nd of an inch maximum on each side. If it is not then you need to adjust one or both sides forward or backwards to get this measurement within the proper specs and then ensure that you have the correct belt deflection and if the belt deflection is then incorrect you need to go through the belt deflection adjustments procedures to get it within the correct specified 10 lb deflection amount while keeping the axle measurements equal within 1/32 inch from side to side.

I do not have the torque or deflection specs for a 1993 FXR at hand so if you do not have them you will need to get them somewhere else.

Sep 09, 2014 | 1993 Harley Davidson FXR Super Glide

1 Answer

Torque spec lb

Hi Anonymous,
Fork stem pinch bolts torque is 30 ft lbs.
Swing arm bolt torque is 50 ft lbs.
Have nice day.

Aug 23, 2013 | 2000 Harley Davidson FXDX Dyna Super Glide...

1 Answer

I need to find the tourqe settings for the swing arm spindle for a Honda CBR 900 RRV. Thanks

The book specified torque for the swing arm spindle nut is 87 foot pounds.

Nov 27, 2009 | 1996 Honda CBR 900 RR Fireblade

1 Answer

I need to know how to replace a 2001 soft tail Harley final drive belt. Does the swingarm have to be removed?

yes buddy swing arm removed belt put behind swing n arm and the wheel losened and slide the wheel forward dont force the belt and after 100miles check the belt tension if so adjust it and also you will require a torque wrench to torque the bolts on swing n arm and on rear wheel the wheel is 100 NM and swing n arm is 79 NM bud

Nov 03, 2009 | 2001 Harley Davidson FXSTB Night Train

1 Answer

Front sprocket

put a 2x4 or similar through the back wheel on top of swing-arm: this will lock wheel from rotating while you crack the nut. 
NEVER put the transmission in gear. 
When re-torquing the nut after refitting, put the 2 x 4 under the swing-arm instead of on top (since wheel will want to rotate opposite direction

Feb 21, 2009 | 2000 Suzuki TL 1000 R

Not finding what you are looking for?
1996 kawasaki ZX-7RR Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4888 Answers


Level 3 Expert

79847 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides