Question about 2002 Yamaha V Star 1100 Classic
Hi, John for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
How to Replace the Voltage Regulator in Yamaha Star 1100 eHow
OEM parts for Yamaha
Posted on May 25, 2016
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1) Make sure your fuel petcock is closed, then detach the gas line coming off it (left underside of tank)
2) Remove the back seat (single acorn nut on rear fender)
3) Remove the front seat (two allen bolts at the back of seat)
4) There are two metric 12mm bolts under the front seat that hold the tank down. Remove them. The tank should be sitting loose on bike, but connected by some wires
5) Disconnect the white wiring harness under the bike. Tank is now totally free to remove.
6) Pull tank up and back at the same time, it will slide off the two rubber mounts at the front.
Posted on Mar 26, 2010
first take scews out or head light unit locaded on either side at 3 n the 9 oclock position they should be a phillips then you should be able to remove the bulb it depends on if light does not work and you have replaced bulb you need to use 12volt test light and check for power on the back of bulb I have had at least 3 times that bulb was good an the spade connection on back of ligt it self if you do not have a test light I would pick one up at walmart or local parts store they are pretty cheap and give lot of advise when chacking fo 12 volt power you need to ground the test light bye attaching its ground clip to anything meatal on motor or fram be ccareful not to put onpainted ares when you take the point end of the test light and check the plugthat attaches to the liht the ligt can be unplugged you should have one wire that lights your light when key is on and one that lights the light only when your high beam indacater is on the other wire is a ground if you have no power on thet plug you need to check fuse for the lights if fuse is good may have problem in handle bar switch if it is the switch try a little wd-40 in the switch an then work it back an forth blow excess out with air hope this info helps
Posted on Aug 05, 2010
I think it is between 2 or 4 thousth of an inch I set mine by ear you want it snug not overly tight or you will lose alot of power before you run the tappid down tight you need all tension of moter run the the adjustment down tight then back it off 1 quarter of a turn lock jam nut down and try there you may be able to go back tighten them a little more hope that will help quiet that noisy upper end down best of luck
Posted on Aug 05, 2010
Tips for a great answer:
Jun 06, 2015 | 2001 Yamaha V Star 1100 Classic
Jul 07, 2014 | Yamaha V Star 1100 Classic Motorcycles
May 11, 2014 | 2002 Yamaha V Star Classic
Apr 24, 2014 | 2000 Yamaha V Star 1100 Classic
Nov 09, 2013 | 2001 Yamaha V Star 1100 Classic
Sep 05, 2012 | 2000 Yamaha V Star 1100 Classic
Mar 28, 2012 | Yamaha V Star 1100 Silverado Motorcycles
Jun 01, 2011 | 2001 Yamaha V Star 1100 Classic
Oct 15, 2010 | 2002 Yamaha V Star 1100 Classic
Mar 01, 2010 | 2002 Yamaha V Star 1100 Classic
160 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: