Question about 2003 kawasaki KX 125

1 Answer

When i put it into first it jumps and stalls would that be the fluid

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Oct 10, 2010

    is clutch adjusted right?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Dont think its a fluid issue. more like a clutch adjustment either at lever or in mid section of cable if that doesnt fix you might have to replace either clutch cable or clutch disks

Posted on Jan 24, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix my truck


ALTERNATOR PROBLEM /THERMOSTAT PROBLEM

Oct 09, 2015 | 1986 Toyota Pickup 4WD

2 Answers

My 1993 Toyota Corolla stalls and will not stay running.


If changing the battery does not solve problem, or only solves it until the battery dies then have the alternator tested. I have noticed on several occasions with a couple of my vehicles that at times of very high moisture in the air they do not stay running, once the humidity goes down they are fine.

Apr 01, 2014 | 1993 Toyota Corolla

1 Answer

1986 Aspencade clutch not working properly, you put in gear bike jumps and stalls. Added DOT4 brake fluid, but I need to bleed the line. Don't know where that is located to do this. Thanks for any help you...


Do I understand you added DOT fluid to your engine to fix your clutch problem?

Clutch is normally activated by a cable while brakes are activated through a master cyclender which uses DOT fluid.

If you have brake fluid in your engine ... get it out immediately. It might be time to get help from your local Honda Shop.

Sep 21, 2010 | Honda GL 1200 Aspencade Gold Wing...

2 Answers

Car runs but when put in gear stalls


if your car stalls or trys to lerch forward when stoping at a light or stop sigh, then your over drive is loked meaning you need to have your transmition serviced or the electrical to the lockup solinoide needs to be checked

Apr 12, 2010 | 1996 Pontiac Sunfire

3 Answers

Just went for inspection, got P0551. no idle


It's an issue with the pressure sensor in the power-steering lines, it needs replacement, if you're going to do this yourself, make sure you do it quickly and try to catch any fluid that might drain from the line in a clean bowl, that way you can reuse it, after installing the new sensor, refill the power-steering fluid and turn the steering wheel lock to lock 20 times, that should bleed any air from the system.

Mar 02, 2010 | 2000 Dodge Durango

1 Answer

2000 jeep grande cherokee, will start if i jump it off, but when i give it gas, it idles down and stalls out


Check your charging system. Jumping will put a slight surface charge on the battery but that will only last as few minutes. If system is not charging, you will drop below operating voltage and the engine will then stall after disconnection jumpers.

Aug 20, 2009 | 2000 Jeep Grand Cherokee

4 Answers

Clutch has no resistance , jumps stalls when putting in gear


i had same trouble with clutch-bike sat for two years--i bled clutch system and it works great now--i found to aid the bleeding process i had to back off the bolt a little at the master cylinder and bleed it there too -same as you would a bleeder screw ((( do try not to get fluid on ur paint-of course)))

Jul 01, 2009 | 1996 Suzuki VS 1400 Intruder

1 Answer

Truck seems to stall while driving.


I have a 1980 GMC 3/4 ton stick shift truck and this past week my truck seems like its stalling as it drives. i had the oil and fuel filter changed this past thursday and it keeps stalling.

Oct 04, 2008 | 2001 Ford Ranger Regular Cab

Not finding what you are looking for?
2003 kawasaki KX 125 Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...