Question about 1986 Honda GL 1200 Aspencade Gold Wing

1 Answer

The clutch lever does not depress clutch so you can get in gear

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Make sure the clutch fluid reservoir on the handlebar is full of dot3/4 brake fluid and bleed the clutch slave cylinder to get the air out. If you can not build pressure or lose pressure after bleeding, replace the seals in the master and slave and bleed again.

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car turns off when engaging clutch to a lower gear


Check the following:
- Thrust bearing, clutch.
TEST: Pull up the hand brake. Start the engine and let it at idle speed.
Depress the clutch pedal, put the car in 1st gear, while keeping the clutch pedal depressed. If the gear lever hesitates or produce any abnormal noise, replace the clutch thrust bearing.
- If the gear lever shifts smoothly, clean the throttle body, idle air control valve and perform idle speed learn learn procedure.
- Check the valve clearance.

Apr 11, 2014 | 1992 Toyota Corolla

1 Answer

Gear lever is not activating but the clutch is fine


problem with linkage cables. get under vehicle and select a gear
manually with engine off, then climb inside, start up with clutch
pedal depressed, release clutch, if nothing happens, problem in gearbox, if it takes off, problem with linkage cables.

Apr 03, 2014 | Toyota Quantum Cars & Trucks

1 Answer

How to shift gears in pulsar 135


Close Throttle & Depress the clutch.
Shift Into next higher or lower gear.
Open The throttle and release the clutch lever slowly and simultaneously.
20065b88-97c5-4838-bddc-4384ea203087.jpg

Feb 15, 2014 | 2011 Bajaj Pulsar 220 F

1 Answer

Have ttr50 2008, starts in gear, doesn't shift properly. you did not list a TTR50 so I picked the TTR125, could you still answer my questions on a TTR50 thanks!


If the bike starts when it is in gear that would indicate that the clutch switch is sticking/broken? It is located between the clutch lever and the clutch lever assembly, normally a plastic bullet shaped switch with a switch that is depressed when the clutch lever is not engaged and released when the clutch lever is pulled in. The not shifting could be down to the chain not adjusted for freeplay correctly, also lub the gear change shaft. If the chain is adjusted then check freeplay on the clutch lever normally about 10mm, but check with your handbook.

Mar 29, 2011 | Yamaha TT-R 125 Motorcycles

1 Answer

Hi, I have recently bought my Mrs a cbr 125r. The bike only starts in neutral. When in gear and the clutch is pulled in, the bike wont start. I disconnected the connectors to the clutch lever switch and...


The reason why the bike wouldn't start while in gear and the clutch depressed is so it wouldn't start and jump ahead if the clutch was released. This is usually called popping the clutch without in gear without throttle.........Hope this helps.

Feb 23, 2011 | Honda CBR 125 R Motorcycles

1 Answer

I know that the bike will only start in neutral with the stand down, but the same is true when the stand is up. Why won't it start in gear with the clutch lever depressed?


You probably have a defective clutch safety switch or it would start in gear when you pull the clutch lever like every other Honda made in the last 30 years.

Oct 05, 2010 | 2003 Honda VT 1100 C Shadow Spirit

1 Answer

Hydraulic clutch gives no feedback at all and after shifting into gear(engine off)rear wheel remains locked with the clutch fully depressed. Have bled lines until no sign of any air remains. Have been...


Does the clutch lever have resistance whiles depressed?
Put your bike on the center stand, select any gear say 2 or 3 , press the clutch lever and thn rotate the rear wheel harder , it may release the sized clutch plates.
Hope this helps!

Nov 28, 2009 | 1983 Honda CBX 550 F-F2

1 Answer

My transmission will not shift into any gears with the engine running and clutch fully depressed. It will shift into all gears without the engine running. I have to place the transmission in first gear,...


Check the fluid level on your clutch slave cylinder. Have someone depress the clutch while visually observing the movement of the levers under the hood. Could also be a bad throwout bearing.

May 08, 2009 | 1997 Pontiac Sunfire

1 Answer

Mitsibishi colt 97 stuck in 1st gear


Your link broke off. What might have happened is the car got stuck in 1st, and when you shifted to second, the link broke. Not too clued up on your car, but you probably need to drop the gearbox. On some cars you can take out the shifter without having to drop the box and still see if the link is broken. Good luck

Mar 18, 2009 | 2006 Mitsubishi Colt

4 Answers

Car will not drive, is it clutch or cabel


my daewoo lanos wont shift into gear/s while running even when clutch is depressed all the way

Nov 12, 2008 | 2001 Daewoo Lanos

Not finding what you are looking for?
1986 Honda GL 1200 Aspencade Gold Wing Logo

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...