Question about 2006 BMW R 1200 GS

1 Answer

Need to replace clutch - 2006 BMW R 1200 GS

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 113 Answers

Is your clutch slipping?? Is there an oil leak between the engine/trans?

Replacing the clutch on a R1200GS is a bit involved unless you are very mechanically skilled. You basically split the bike in half to remove the transmission and gain access to the clutch.

If the clutch is NOT slipping, I would suggest removal of the starter motor on the lower LHS of the engine/ trans. and measurement of the clutch disc before you start the work of disassembly.

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch and engine check light plus clutch got eaten up in 2 weeks time


If ur have replace ur clutch but the check light still on it mean your CO sensors need to clean or replace.

Jun 17, 2016 | Nissan Cars & Trucks

1 Answer

Transmission slipping


This normally means your clutch is worn down and needs replacement. Much less likely is that the clutch pedal travel needs adjustment.

Replacement of the clutch requires removal of the gearbox and is much easier with a shop hoist. I'd recommend replacing the pressure plate assembly as well.

Jul 31, 2012 | 2003 Toyota Corolla

1 Answer

I recently purchased a 2003 hyuandai tiburon GT with 171k miles on it i was on the interstate doing 80 mph in 4th gear at around 6k rpm when my clutch pedal dropped back into the floor board and just...


hmmm... 80mph @6000 rpm is not normal. you are needing a lot of power to produce 80mph. it seems clutch assembly needs replacement. clutch assembly includes clutch disc, fly wheel, and release bearing. might as well check your clutch master if the vacuums are still working properly. this might be the culprit to the stuck up clutch pedal.

after replacing the clutch assembly, you can reach 80mph @ 4000-4500rpm

Aug 06, 2011 | 2003 Hyundai Tiburon

1 Answer

Replaced master and slave clutch cylinders but


if you replace and shure to make a good bleed on clutch fluid, then replace clutch disc

Jul 27, 2010 | 1991 Toyota 4Runner

3 Answers

I have a zx7r ninja and yesterday it worked fine today its like the clutch isnt working at all when i go to click it in first it jumps and dies the fluid is full


Clutch plates may have worn out OR If hydrolic clutch then it may need re-bleeding or if cable- May need replacing or adjusting
Check them few things you will most likely find its the clutch plates need replacing.

Jul 08, 2010 | 2000 kawasaki ZX-7R

2 Answers

Clutch needs adjustment


as the clutch wears the "free pedal" is reduced ... its easy to adjust "free pedal" and important to do so .. when there is very little or no free movement above where the clutch engages/disengages then the clutch starts to wear rapidly ... if there are no other symptoms like clutch chatter, slipping or noise then the clutch plate likely has some life left if it is adjusted properly and promptly ..

Feb 22, 2010 | 1994 Nissan Pickup

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

Hi i have a peugeot 406 2.0 hdi 1999, when i get in the car the clutch pedal is on the floor and i have to pump the pedal for a couple of minutes, then it is ok to drive. any ideas what is wrong with it?


The clutch acting system is hydraulical, (clutch hydraulic system).
Your clutch pedal master cylinder is weak, and needs to be replaced or repaired by gasket kit replacement. Also the clutch slave cylinder can be used, and needs to be repaired (by gasket kit replacement), or replaced. The clutch system must be bled after carrying out work on the hydraulic clutch mechanism.

Dec 09, 2009 | 2006 Peugeot 504

2 Answers

Same issue, wondering if I can replace the clutch myself?


Hello kj_jung,
Good for you to DIY the clutch replacement. I assume you are taking dc/UC errors in spin cycle. I have put together a step by step process which some pic’s. A number of folks have tried the process with success. Take a look at this post and save yourself some money. I did not need to replace my clutch just a WD-40 clean up and re-lube of the One-way Roller clutch bearing. I did replace the clutch with this Clothes Washer Clutch - 25001169 clutch just to see if it would work several months ago to possibly offer folks a better cost replacement for the clutch. It works fine, AZ just raised the price from $48 to the current price. APP has the clutch for about the same price. While you are waiting for the clutch try to clean up the One-way Roller clutch bearing and re-lube to get back in service. It's good practice. I'm an owner like you with an my front cover removed can remove replace the clutch in 5 to 7 minutes. When I first tried this it took me 20 minutes and the clutch spun off. I detail what the SM speaks of in getting the clutch pully seated properly. As I state in that post you don't need a torque wrench, just seat the clutch properly and snug the clutch pulley 3/8" bolt.
My repair process for clutch maintenance/replacement was hosted also on this respected DIY forum I was helping a forum member on that site with a FAV9800AW clutch issue for the famous dc/UC errors in spin cycle.
Post back if you have questions and Good Luck. Rich

Aug 12, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Clutch repair 2005 VW Chico


You need to empty the engine from all fluids, tehn remove air filter and other parts, mount your Golf on a bridge and remove the clutch pressure plate assembly mounted on a side of the engine.

You will need special tools to align and mount the new pressure plate, and you will need to follow a procedure to reinstall the clutch without removing the transaxle.

Replacing the clutch is not an easy task for a beginner, if you do it yourself, get the haynes manual with the complete illustrated procedure.

After replacing you will have to adjust the clutch. See CLUTCH REPLACEMENT PROCEDURES.


Feb 17, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
2006 BMW R 1200 GS Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...