Question about 1993 Honda VT 600 C Shadow

1 Answer

How do I remove the ignition key on a VT600c 93 off its mounting?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Take the screw out of the chrome ignition switch cover. Remove the cover. There are two bolts that hold the ignition switch on. you may have to drill or grind off the tops of the bolts if they are anti-theft bolts. You can replace them with standard screws or bolts.

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition system diagram


Remove gaiter from around gearlever.If I remember correctly turn key to a position between off and lock and using a piece of wire bent at the end insert into the small hole approx 1inch from top and depress the pin which holds the lock barrel and lift out.

Jun 26, 2014 | 2008 Saab 9-3

1 Answer

Can I put a 93 honda shadow vt750 fuel pump on my 93 honda shadow vt600


Hi, Anonymous after careful deliberation 4 out 5 Honda Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Bridging The Fuel Pump Relay
Way around the VT1100 Fuel Pump problem
Honda VT600C Shadow VLX Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda VT600C Owner Manual

May 10, 2014 | 1993 Honda VT 600 C Shadow

1 Answer

What is the procedure to changing an keyed ignition lock?


Hi there,

Removal

Disconnect the negative battery cable with the proper size wrench and place away from the battery.
Insert the key into the ignition lock cylinder and turn the key to the run position.
Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.
Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.

Installation

Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
Install the electrical connector back into the connector housing by pressing it in with your hands.
Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.

Hope these help.

Jan 28, 2011 | 1992 Ford Crown Victoria

1 Answer

How do I change the ignition switch in my 93 plymouth van?


FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Sep 18, 2010 | 1993 Plymouth Voyager

1 Answer

Remove broken ignition key on 93 dodge spirit


try prying a small flat head screw driver like something you would use for eye glasses or try a very small drill bit and drill slowly in to key to pull out,or call a locksmith

Jul 29, 2010 | 1991 Dodge Spirit

1 Answer

1999 saab 93 manual, key wont turn in ignition,


I had the same problem the only solution was to replace the ignition barrell

Jun 19, 2010 | 1995 Saab 900

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

93 chevy pickup won't start unless in neutral


Put the trans in nuetral and see if it starts normal with key. If not, then the ignition swith is suspect. The actual switch is mounted on top of the steering column on the lower end. It is actuated by a rod. the key has no electrical. or your trans linkage needs adjusting. Good luck, Ned-

Sep 16, 2009 | 1993 Chevrolet K1500

Not finding what you are looking for?

Open Questions:

See all 1993 Honda VT 600 C Shadow Questions

1993 Honda VT 600 C Shadow Logo

326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...