Question about 2002 Kymco Hipster 125

1 Answer

Hi . where is the valve timing mark on my kymco-125 hipster cam -sprocket.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

The valve timing mark is on the flywheel on the Hipster's.

Remove the large flat blade screw from the top of the left hand side casing. Turn the engine either by hand (using kickstart with ignition off), turning rear wheel in gear, or by removing the "kymco" badge with three 8mm bolts and using a 19mm deep socket on the crank, until you see two marks (one says F one say T) the F one is the advance firing mark, the T mark is the timing mark. Keep turning the engine over and watch your valves, wait for the exhaust valve to close, inlet valve to open and then close again then the next time you see the T line will be TDC. This is where you set your valve timing from.

Posted on Aug 18, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 397 Answers

SOURCE: i have a kymco hipster

Check your fuses and if they're good, check the connections at the far end of the battery cables. If they are clean and tight, check the battery cables themselves for continuity. If all of the above are good, start troubleshooting from the keyswitch back. If you know which terminals to jump out at the keyswitch for the lights, jump them out; if the lights light up, suspect the switch.

Posted on Jun 25, 2011

tinualbinale
  • 436 Answers

SOURCE: what is the valve clearence

Valve clearance for Kymco Spike 125 ( cold )
Intake - 0.12 mm
Exhaust - 0.12 mm
If you have any doubts don't forget to post me a reply.If you are satisfied please rate my solution.

Posted on Jun 04, 2011

  • 72 Answers

SOURCE: timing headcam

get a manual for it and then you will be able to do any thing you have to do , when the time comes.

Posted on Mar 27, 2009

  • 2 Answers

SOURCE: battery removal

hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Kymco Hipster 125 how to remove the rusted exhaust bolts


Hi, John you may want to try using some penetrating oil or an "Easy Out" or just drill it out, for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
What is the best way to remove stuck rusted exhaust bolt
Removing Tough Exhaust Bolts
KYMCO Hipster 125 Service Repair Manual Download Download Manuals Technical $15
Part Diagrams
KYMCO ZING 125 Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Mar 05, 2018 | 2003 Kymco Hipster 125

1 Answer

Parts for kymco hipster 125cc


Hi, David for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Quality Replacement Parts For Kymco
Hipster 125 2V Hipster 125 4V RJ25AA RH25AA Kymco Scooter Parts Racing...
Genuine Kymco spare parts
KYMCO ZING 125 Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 05, 2016 | Kymco Motorcycles

1 Answer

How do I set the valve timing on a kymco zing 125 cruiser


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kymco, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
how to set and adjust the cam and cam chain timing 4 stroke engines ATV...
How To Set Cam Timing
Valve Cam Timing
KYMCO ZING 125 Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



Aug 02, 2016 | Kymco Motorcycles

1 Answer

WHAT IS IGNITION FUSE SIZE ON 125 KYMCO HIPSTER 2005


Battery Fuse : 20A Reserve Fuse :15A Headlight Fuse : 15A Radiator Fan Fuse : 10A All Electric Power Fuse :15A

15 amp

Apr 10, 2015 | 2004 Kymco Hipster 125

1 Answer

Kymco hipster 125cc service manual free


potrzeb?je insterukcie obs?ugi do kymco hipster 125

Mar 25, 2012 | 2003 Kymco Hipster 125

1 Answer

Derestrict kymco hipster 125cc


The answer (rather late :P) is Yes! You can buy a derestricted CDI from somewhere like wemoto.com I expect, which helps with the top end speed. You can also up or downgear the bike. I've got 4 teeth less on my 2001 Hipster (rear sprocket) and I can accelerate like a ***** (faster than most boy racers off the line) and easily outstrip bikes like the 2012 YBF125 and the 2002 CBR125 on the strip. That's all I've done (other than freeing up the exhaust by shoving a screwdriver down the little holes at the end of the exhaust and smacking it with a hammer - sounds deeper too) and take the side off of the air box filter and put a cleaning sponge in place of the original filter (That warbles quite nicely too)

Mar 24, 2012 | 2004 Kymco Hipster 125

1 Answer

2002 Kymco Hipster 125 will not turn over


Hi, Anonymous before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike won start any ideas
What Do Check When My Motorcycle Won Start Honda Shadow Forums Shadow...
Kymco Hipster 125 150 Motorcycle Complete Workshop Service Repair Manual... $20
Genuine Kymco spare parts
Manuals Kymco

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 11, 2017 | 2002 Kymco Hipster 125

1 Answer

How to tune the timing chain of a 4 stroke motorcycle


crankshaft at tdc, cam sprocket marks in proper position with locator marks on engine, ( this usally means on single cyl the valves will not be loaded by the cam) front of cam chain taught, proper tourque on cam caps realese cam chain tensioner, rotate engine 360deg slowly by hand with spark plug removed, then re check cam timing is accurate..

Oct 31, 2009 | 2005 Kymco Stryker 125

1 Answer

Battery removal


hi,

Remove the plastic panel on the left side of the bike just under the seat and you will see the battery. unscrew the metal bar that holds it in and simply slide the battery out.

Dec 11, 2008 | 2003 Kymco Hipster 125

Not finding what you are looking for?
2002 Kymco Hipster 125 Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...