Question about 2006 Victory Hammer

Open Question

Replaced the factory turn signals on a vic hammer with halogen. purchased a load equilizer. looking for info on proper install.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parking brake equilizer assembly


Care to tell me what you call the equalizer? Also without any info as to make, model and year very hard to answer any question.

Sep 04, 2016 | Cars & Trucks

1 Answer

99 Suzuki VZ800 Maruader. Replaced back blinkers with after market bullets ( non LED ). had a fast blink on Right side. Replaced front same bullets as back. No blink at all. Replaced flasher with a load...


Hi, Mike before testing any electrical component in the Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Turn signals not working
How to install aftermarket turn signals
Suzuki 1997 VZ800 Service Manual
OEM parts for Suzuki
http://mybikemanuals.com/suzuki

Aug 01, 2017 | 1999 Suzuki VZ 800 Marauder

1 Answer

2011 Honda VT1300CS rear turn signals not working


Hi, Daniel before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Turn signal electric problem Honda Sabre Forum VT1300CS Testing and replacing the turn signal relay on Honda shadow 1100 Honda Motorcycle Service Manual VTX 1300 and all Honda Video http://www.partsfish.com/page/oem-parts-for-honda
http://mybikemanuals.com/honda/honda-vt-owners-manuals

Oct 20, 2017 | 2011 Honda VT1300CS

1 Answer

How to tune properly


make sure your speakers are wired to the amp with correct ohm load, turn gain, bass boost all the way down on amp, zero out your equilizer on the cd player and turn it all the way down then start raising volume on cd player., when u can start hearing music thru the subwoofers adjust the cd player volume till the sound from your subs is at its peak without any distortion. then start raising the gain on your amp till you are happy with the sound. It gives you the optimal signal strength coming from the cd player and the smoothest sound.

Jan 13, 2011 | Performance Teknique ICBM-774 Car Audio...

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

Need to know what size bulb goes in dome light


For 1991 TOYOTA Pickup replacement bulbs, review the list and check it in other brand with this model:

High & low beam headlamp
H6054
H6054ST Silverstar High Performance Lighting: The Whiter and Brighter Halogen
H6054XV XtraVision Halogen - The Brighter Light
H6054CB Cool Blue Halogen - The Whiter Light
H6054LL Long Life Halogen Upgrade: Lasts 6x longer

Parking light
168
168LL Long Life Upgrade: Up to twice the life of the standard lamp
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Front turn signal
1156
1156ST Silverstar Signal Lighting: Complete the Look: Crisp, Clean, Style
1156LL Long Life Upgrade: Up to twice the life of the standard lamp

Rear turn signal
1156
1156ST Silverstar Signal Lighting: Complete the Look: Crisp, Clean, Style
1156LL Long Life Upgrade: Up to twice the life of the standard lamp

Tail light
1157
1157LL Long Life Upgrade: Up to twice the life of the standard lamp

Stop light
1157
1157LL Long Life Upgrade: Up to twice the life of the standard lamp

License plate
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp
89

Back up light
1156
1156ST Silverstar Signal Lighting: Complete the Look: Crisp, Clean, Style
1156LL Long Life Upgrade: Up to twice the life of the standard lamp

Front sidemarker
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Glove box
161
161LL Long Life Upgrade: Up to twice the life of the standard lamp

Step/Courtesy light
DE3022
DE3175
DE3175LL Long Life Upgrade: Up to twice the life of the standard lamp
7443LL Long Life Upgrade: Up to twice the life of the standard lamp

Hope helped with this (remember rated this help). Good luck.

Nov 11, 2009 | 1991 Toyota Pickup

2 Answers

Factory radio main key to ignition switch


The factory radio has nothing to do with a car starting or not starting. You can install any radio that you like in your car as long as it was installed properly there will be no problem. The no start needs to be looked at but don't look at radio for cause. Would need more info on the no start to help there. You should take notes as to conditions when car won't start.

Sep 30, 2009 | 2000 Chevrolet Impala

2 Answers

1999 ford crown vic dash light running light problem.


Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.
Vitally

Sep 09, 2009 | 2000 Ford Crown Victoria

1 Answer

Front turn signal bulb replacement


HEADLAMP BULB REPLACEMENT

REMOVAL PROCEDURE

CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

  • Turn off the lamp switch and allow the bulb to cool before changing the bulb.
  • Leave the lamp switch OFF until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Keep dirt and moisture off the bulb.
  • Properly dispose of the used bulb.
  • Keep halogen bulbs out of the reach of children .
NOTE : Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.


  1. Open the hood.
  2. Remove the headlamp. Refer to Headlamp Replacement .
  1. Remove the access cover from the rear of the headlamp.
  2. Disconnect the electrical connector from the socket.
  3. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  4. Disconnect the electrical connector from the socket.
  5. Remove the bulb and socket from the headlamp.
INSTALLATION PROCEDURE

IMPORTANT :
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.
    1. Position the bulb and socket to the headlamp.
    2. Connect the electrical connector to the socket.
    3. Install the bulb and socket to the housing by rotating the bulb and socket clockwise, locking the retaining tabs to the housing.
    4. Install the access cover to the rear of the headlamp assembly
    5. Install the headlamp

REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the headlamp.
  3. Rotate the bulb and socket counter-clockwise in order to remove the bulb and socket from the housing.
  4. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.
INSTALLATION PROCEDURE


  1. Install the side marker bulb (3) or turn signal/park bulb (4) to the socket.
  2. Wipe the bulb with a clean cloth to ensure the bulb is free of any dirt or oil.
  3. Install the bulb and socket to the headlamp by rotating the bulb and socket clockwise, locking the retaining tabs to the headlamp.
  4. Install the headlamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

03 harley sportster, hooked up new led turn signals on bike, when motor not running they work fine, start the bike and they flash about 3 times and stays on. anybody got the same problem?


The load on the LED lamps is too low for the turn signal control box. there is an equilizer box available you have to put in line with the signals to get the load back to where it needs to be.
In it's current condition it beleives a light is burnt out.
you can get the device at your local dealer or on line .

Mar 14, 2009 | 2003 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
2006 Victory Hammer Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4731 Answers

Joseph Hoffmann

Level 3 Expert

1746 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...