Question about 2004 Skyteam ST 125 Y

1 Answer

Change the clutch cable? How do you set the right settings?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Once you change the clutch there are two adjusters , one up at the lever and one just before the bottom connector which pulls the clutch

Posted on Jun 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1991 Prizm. When I release clutch in first, why doesn't it go?


1991 Prizm (aka, Corolla) dead clutch (aka SLIPS)
does engine crank and start in gear? in gear?
the first thing to check is the clutch pedal actuation system.
cable on some , and Hydraulic on othere
open hood, see that MC for clutch, is the Reservoir dry?
yes, no?
yes, then the slave or mc is bad or both, the one leaking is bad.
Most cases Hydra clutches can not cause slip. (rare)
its a cable, can if cable frays inside or rust, (big time common)
well all cable clutches need service, if not it fails.
called setting free play in the book, FSM book
I love the above post where he guesses then sets a price.
first is diagnosis prices last and varies all over planet earth
and is useless here. prices. always.
Ill look in Michell's for you.
it's not a cable system,
Mitchells shows, hydra. clutch
so unbolt the slave.(on bell)
start car in gear, does car move. yes /no?
yes, clutch ok , and slave is siezed.
no, then clutch is bad (inside bell housing) $$$$$

i posted both ways, as these era cars run to clutch systems.
that could even change mid year, production.

S= slave
Bell = bell housing
L = clutch lever.
see the 2 bolts?
some Slaves can seize (due to running old fluid full of water)
Dot3 fluid is hydrascopic and needs service every 2 years. min.
26082435-4gmiw4kjhjrck3uewcae1lzo-4-0.jpg we check the MC and all parts related here.
to see if the L lever is stuck to the right above.
never condemn any clutch until these checks are done
or go broke fast. IMO

Feb 05, 2016 | Geo Cars & Trucks

1 Answer

I have a Suzuki swift 2007. I have the clutch changed and gearbox recon,but still hav the same problem. When the car is hot the gearbox becomes so stiff dat it's very hard to change gear plz help


has a manual transmission? (only clue was very hard t change, you or it?)
Answering for M/t box. (nobody ever posts what they drive first. (DRIVE LINE)
bad clutch cable? be first.
or is it hydra. clutch actuator. (fluid low?)
fluid drops day by day, bingo.
you skipped diagnosis and jumped to changing expensive parts.? wow, $$$$$$$$$$$$$

using wrong trans fluid.?
clutch cable/or slave/mC bad.?
clutch drags.?
if cable , pedal free play not set right. (lose)

Dec 03, 2015 | Suzuki Cars & Trucks

1 Answer

I want to know how to set my clutch on my 1983 GPZ1100


When you say set your clutch, what do you need to know? Are we talking about the clutch lever, if so here is what you will need. One nickel, place the nickel between the lever and perch. Adj cable out so when you pull on the lever you feel tension right as the nickel falls out. This amount of play will insure the plates are closing the whole away. If you need help on the other end of the cable please feel free to contact me M. Woodring

Nov 29, 2013 | kawasaki GPZ 1100 Motorcycles

1 Answer

Page 6-4 from 79 fx harley davidson superglide manual got messed up. need info on clutch adjustment.


Loosen the cable adjustment that's on the right side of the bike just behind the starter solenoid. Turn the adjuster in a good bit. Remove the derby cover and loosen the lock nut in the center of the clutch assembly. Turn the adjusting screw inwards or outwards to adjust the position of the clutch release arm. Seems like 1979 was a transition year in which they changed the type of transmission that was used in the bike. The early models used the rotary top transmission and the late models used the rachet top (cow pie) transmission. If you have the rotary top transmission, adjust the center screw of the clutch until the gap between the starter and the release lever measures 3/8" to 5/8". If you have a ratchet top (cow pie) transmission, set the gap between the release lever and the small diameter section of the top of the shifting mechanism at 13/16". Once you get this set, go back to the cable adjuster and turn it outwards until you have about an 1/8" freeplay in the cable.

Good Luck
steve

Jul 05, 2011 | Harley Davidson FXR Super Glide...

1 Answer

Not changing pass third gear had transmission rebuilt twice in past year, fluid is fine Rpms race to five


Hi :) Sounds like the clutch pack if the machanic didn't setup the T.V. Cable The right way the hydraulic pressure wouldn't be properly set and as you are driving the clutches would be slipping everytime they change gears and since you use 3rd and 4th the most they go first.

May 06, 2011 | 2000 GMC Yukon

1 Answer

My mate changed my clutch with a new set,new cable etc.. But its so hard to switch gear,looks like it has not enough pull distance,now after changing the settings a bit its in gear and when pulling the...


Did you set up the clutch mechanism/pushrod correctly? Where the clutch cable goes into the engine you need to remove the cover to access it. First off, set some freeplay into the cable by either/and adjusting the lower end of the cable or at the lever.
Once done, under the cover you will see a lock nut on the end of a shaft with a slot in it for your screwdriver. Slacken the lock nut. Turn the shaft in (clock wise) until you just feel resistance. Now back it out half a turn. Secure the lock nut ensuring the centre shaft does not turn. Now set the freeplay in the cable to give a few mm's play at the lever (you may be able to acheive this with just the knurled adjuster at the lever end, if not use the inline adjuster at the point where the cable goes into the engine cover). Make sure this is right before the hassle of checking the plates.

Feb 12, 2011 | 1980 Suzuki GS 750 L

2 Answers

My 2007 650 Burgman is slipping on takeoff.It runs fine after you get it moving.


Check there is at least 1/2" play at the little finger end of the clutch handlebar lever, if there isn't loosen the cable off until there is. If there is, adjust/replace the clutch plates as required. It may be just the clutch spring if you are very lucky!

Jan 04, 2011 | Suzuki AN 650 Burgman Motorcycles

1 Answer

Clutch engages to far from the hand grip


if you follow clutch cable down you will find your mid range adjustment use 1/2 in and 9/16 in wrench and back off now go down to your primary cover and remove inspection cover (where clutch cable goes into primary cover) take off cover and spring hex nut.with screw driver turn adjusting screw counterclockwise until lightly seated back off 1/4 to 1/2 turn replace spring hex lock (spring facing out) go back to mid-range adjuster on cable adjust so you have an 1/8 in free play (you can use a nicheol) to set freeplay at lever pull lever in three times to check and set

Jan 08, 2010 | 2007 Buell Lightning XB12S

1 Answer

Engine


Valeo car parts does a clutch assembly complete with modified flywheel as well,so its a conventional type clutch without being the back to front one thats fitted from new.BUTS ITS EXPENSIVE about 800€ but it works

Feb 17, 2009 | 1987 Peugeot Liberte

1 Answer

Adjust Motorcycle Clutch Cable


Usually there are 2 adjustment points. One at the clutch lever, and one on the clutch pull on the crankcase. Follow the cable from the handlebars to the engine, there should be an adjust bolt or two. The adjustment at the handlebar lever is usually a screw with a thumbwheel lock nut. Depending on what you are trying to adjust, dictates which one you will use and in what direction it will go. If the clutch is slipping, use the thumbwheel adjuster. Loosen it, back the screw out 2-3 turns, tighten. and check you clutch. if this one is all the way out, go to the crankcase, loosen the bolt on the richt side of the bracket first, then loosen the left one, one turn at a time, checing the clutch. once it's where you want it. tighten the right bolt only. You can do this with a set of open end or box wrenches. An adjustable wrench works in a pinch.

Nov 27, 2008 | 2006 Honda FMX 650

Not finding what you are looking for?
2004 Skyteam ST 125 Y Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Skyteam Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

41660 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Are you a Skyteam Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...