Question about 2003 Yamaha WR 250 F

1 Answer

How do i remove the seat please? - 2003 Yamaha WR 250 F

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

There should be 2 10mm nuts holding it on

Posted on Oct 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove drivers seat


There are four bolts underneath the seat. Unscrew them then lift the seat slowly, please take care when removing as there are some connections you may have to remove from the connectors before removing the seats.

Jul 15, 2014 | 2006 Renault Laguna 2.0

1 Answer

How do you remove the battery from a Suzuki van van 125 motorbike? mine is flat and i need to remove it to charge it up again.


On my TW125 Yamaha very similar to the Van Van. the battery is under the seat. There are 2 6mm bolts that fix the seat to the sub frame. Try using a torch or light and look under the seat from the chain side. The only other method of seat fixing i am aware of on Suzuki bikes involves removing the plastic panels under the seat and this reveals the seat fixings. Please remember when you remove the battery undo the negative lead first. Please do not use a charger with an output of more than 1 amp. When you refit the battery please connect the positive lead first.

If the recharged battery works OK please check the charging circuit is OK. Connect a volt meter across the battery terminals and see if the volts rise to about 14.5 as the revs are increased. Hope this helps

Feb 03, 2011 | 2006 Suzuki RV 125 VanVan

1 Answer

In order to change from the toddler seat to the booster for a child over 40 lbs, what do I do?? does the seat just become attached to the car by the seat belt? does it need to be attached by other...


Hi,
please feel free to call at 1-800-544-1108 and they can send you a manual in case you dont have it.

*To convert the car seat into a booster seat, turn the car seat over and remove the pin that holds the base in place. tHEN REMOVE THE BELTS AND THE BUCKLE.
*To remove you need to bend/twist the keeper until you can push it UP through the seat and remove the belt/strap. It is now a booster seat for use with a lap/shoulder belt in the car. Store all the parts you removed in a ziploc bag for when your child outgrows it so it can be reused

PLEASE RATE MY HELP :)

Sep 17, 2010 | Cosco Alpha Omega Elite 5-Point 22-155

1 Answer

How do you remove the rear seat in a 2002 Mercedes C240?


please check below the rear seat you can see small plastic cover have fitted near seat it's same color of your interior carefully remove that plastic covers without braking locks then you can see bolt for remove rear seat cushion remove bolts and slide the cushion towards front.

Sep 14, 2010 | 2007 Mercedes-Benz C230 Sedan

1 Answer

Remove the back seat from chevy celebrty 1987


Push lower end of rear seat back to unlock clips (takes a bit of effort)
Lift bench out
Should be clips or bolts holding the top of the rear seat - release these
Push up on the upper section of seat to release top clips.
in some car models
Remove the 10mm bolt behind the bench near the seat belt fastening sight and then lift the seat up from the back to the front..towards the front seats. The clips are angled down and in so that the back has to lift up first.
This will help. Thanks please keep updated. please please do rate the solution positively .thank you for using fixya

Mar 18, 2010 | 1987 Chevrolet Celebrity

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

Seat removal on a ybr125


Remove both side panels, and remove the 10mm bolts that are just below the seat. Should just lift off

Apr 17, 2009 | 2007 Yamaha Ybr 125

3 Answers

Unable to remove seat to replace batteries


Sometimes it just takes two really strong people to remove these seats. Especially if it is that old. I`m not saying damage the chair,but i`ve had some that were almost impossible to remove.

Mar 17, 2009 | Electric Mobility Shoprider Electric Power...

3 Answers

Remove drivers seat


There are Bolts Underneath the Seat Inside of the Frame Rails. Remove these and the Seat Belt from the Seat if attached and Unplug the Wiring Harness Under the Seat if they are Power Seats. Please Rate My Response! Thanks!

Feb 06, 2009 | 2000 Buick Century

1 Answer

I need to replace the front driver's seat in a 95 saturn...


seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

Jan 06, 2009 | 1995 Saturn Sl

Not finding what you are looking for?
2003 Yamaha WR 250 F Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...