Question about 1984 Honda GL 1200 Interstate Gold Wing

1 Answer

One cyllinder is compressing at 110 and the remainder at 92

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Squirt oil in your cylinders and recheck the compression. If your compression goes up you have bad rings. Check your valve tolerances to make sure that the valves are not being held open only because they are adjusted too tight. This would cause compression loss. If the valves were bent because the timing belts slipped or broke You may have to replace the valves to get compression back up. If the engine has low compression because there are 300,000 miles on the bike you may just need a complete overhaul or a new motorcycle. If you had at least 110 compression on all cylinders and they were all with in 10 pounds of each other you could still be riding on low octane fuel.

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 mazda millenia # 1 cylinder low compression


If you are putting air in the cyllinder, it can go out the valves. The only way to check compression is with compression tester.

Feb 09, 2013 | 2001 Mazda Millenia

1 Answer

Loss of compression in #5 cylinder on my 1990 nissan maxima


I would first be sure that you have spark to that cyllinder. Pull the wire off and stick an extra spark plug in the wire. Lay it on the engine block somewhere and atart the car to see if it's sparking. If it is, you have a valve or cam problem. If it isn't check the plug, the wire, distributer, coil pack etc.

Jan 14, 2013 | 1990 Nissan Maxima

1 Answer

Chainsaw do not start


have you checked the spark to see if you are getting spark and then check the compression it needs to be 110 psi min, to do thisyou have to have a compression tester you can get one at any auto parts store (step one remove the spark plug screw in the compression tester with the right fitting then pull the starter rope 5 times and the compression should be 110 psi if it does not read a min of 110 psi the engine will need to be rebuilt and it is not worth doing it will cost 300-400$ to rebuild the motor... email if you have any problems whitejeff74@yahoo.com

Jul 21, 2011 | Homelite Garden

1 Answer

Intruder 400 carburettor model. rear cyllinder not running smooth, making a sneeze sound by the left exhaust pipe. please help!


sounds like a bad head gasket, pull the plugs and do a compression check if the cylinder arenot within 10% of each other time for some real work.

Feb 25, 2011 | Suzuki Intruder 400 Motorcycles

1 Answer

6th cylinder misfire. replaced spark plug and ignition coil 6 months ago and already misfiring again.Is this a problem with 2000 toyota tundras or is this normal to have to change spark plugs and ignition...


Did u find code p0306 comes up ? Two things can cause this if the plug and coil have been replaced.the intake manifold may be leaking in the area of cyllinder 6 or its a mechanical issue.try doing a cyllinder misfire test and also check the compression on all cyllinders

Dec 16, 2010 | 2000 Toyota Tundra

1 Answer

What do you set the torque at on the head of a 1997 jeep cherokee grand laredo?


I'll try to make this simple.
Draw a rectangle and then draw seven bolt holes on each edge.
number the top (will be right side of engine) this way> 12,8,4,1,5,9,13.
Second row starting under #12 is:11,7,3,2,6,10,14.
Bolts are torqued in a spiral in order, 1 through 14 at 22 foot pounds, again at 45, again at same, again at 110 but #11 goes to 100, not 110 (this bolt also gets sealant on threads to prevent seepage) then continue with remainder in order at 110 pounds.

Sep 02, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

92 toyota pick-up huge idling problem


Check compression, my truck did the same thing and I had no compression on one cylinder and had to have a valve job done.

Jun 01, 2010 | 1992 Toyota Pickup

2 Answers

98 volvo S70: Won't start


it is either out of time or you have bent valves

Apr 14, 2010 | 1998 Volvo S70

1 Answer

How do you remove the clutch master cyllinder on


You must remove the transmission since the slave cylinder is mounted in the bellhousing on the M5OD transmission your truck should have

Mar 17, 2010 | 1992 Ford F150 SuperCab

1 Answer

1992 Geo Storm having problems.


you may have turned too many rmps and warped a piston which would cause the piston to actualy hit your valve, or while turning too many rpms you may have caused the valve to "float" which would mess it up

Sep 13, 2008 | 1992 Geo Storm

Not finding what you are looking for?
1984 Honda GL 1200 Interstate Gold Wing Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...