Question about 2006 Honda CBF 250

3 Answers

I accidently laid my Honda CBF250 down on its right side. Now the starter motor won't mesh with the engine to turn it over. How do I realign the gears to make it work?

Posted by on

  • swanson467 Oct 04, 2010

    I have a servic emanuel. This is not covered in the manuel. That is why I am asking you.

    Regards

    Don

  • swanson467 Oct 04, 2010

    Hi



    Thaks



    It sounds do able. I tried that but did not detach the power. Do I need to replace the whitish lubricant that escapes when I open the cylinder?



    All the best




    Don

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

The cover is bent,causing mis-alignment. You most likely will need to replace the entire cover and bolts.

Posted on Oct 05, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 11,800 Answers

You need to take out the starter and inspect it thoroughly - check every single part for deformations. Then check the solenoid .
If everything is ok then put it back but don't connect the power cables yet and keep the bolts lose. Adjust the position of the starter for perfect mesh then check the fitting of the case of the starter to the case of the carter - if there is some play in there then one of them was deformed.
You now have 2 options: either file the support that sticks out or you insert some shims on all the others.

Posted on Oct 04, 2010

  • Azrael SRL Oct 05, 2010

    Yes, it's a silicone based grease that is extremely important for the cooling of the starter.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

Here is the link to the service manual of CBF250. IT has all the diagrams of parts and adjustments and maintenance tips:--
cbf250manual

Thanks. Keep updated for any more query. You can rate this solution and show your appreciation

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermostat for the carb heater on my Honda CBF250-4 Keihin carburetor?


Hi, Brian the thermostat is usually located on the side of the airbox for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Honda Cb250 Cb360 Cl360 Cj250t Cj360t 1968 1979 Service Repair Manual
http://www.partsfish.com/page/oem-parts-for-honda
http://campaigns.hondampe.com.au/Motorcycles/manuals/CBF250.pdf

Jun 15, 2016 | Honda Motorcycles

3 Answers

Where i can find the starter for honda civic dx 2008?


The starter should be located on the left side of the engine. That is the side nearest the front of the car. Typically the transaxle spans a portion of the right side of the engine. You may also find related info on tha Autozone website. Enter your vehicle info then go to "view job diagram" on the right side of the page.

Oct 11, 2012 | 2010 Honda Civic DX

1 Answer

Starting


Could damaged flywheel teeth where starter mesh. Turn the motor by hand a half turn and then try starter again. Does the vehicle start when you push or tow it?

Jun 25, 2012 | 1984 Honda Accord

1 Answer

HONDA ACCORD Seats Front Assembly Recliner went down and won't go up


I wouldn't ruin anything by trying things yourself

I would have a dealer check it out

The dealer I used in the past, has a seat specialist come
in on Wed only, around 5:30 after the service bays close
& one service writer hangs out until that person fixes a
couple vehicles seat issues

Jun 12, 2012 | 1995 Honda Accord

1 Answer

Engine starts fine, runs fine for about 5-10 minutes of various speeds. Then it shuts down suddenly regardless what trottle possision. Engine will start right away again, but promblem will accure after few...


Could be so many things, I know on modern Harleys there is a shut off relay that turns off the engine if the bike is on its side. If that switch goes out, the motor won't run. Probably have to take it to the dealer.

Jul 08, 2011 | Honda Fusion Motorcycles

1 Answer

We just put in a new starter but when we connect the battery sparks come out


Two causes of this (if sparking occurs when sarting is attempted):
(1) teeth on new starter not properly meshed to flywheel
Cause: installation of new starter not securely or properly bolted down.
(2) new starter motor itself is faulty right out of the box.
Cause: poor manufacturing/rebuilding quality control by starter mfr/rebuilder.

Also, if sparking occurs when battery connected (and the sparks come from the battery connector),
then the starter is improperly wired.

So, where are the sparks coming out of?

May 14, 2011 | 2004 Honda Accord

1 Answer

I have a Honda accord that needed a new starter. Now the mechanic says I have to replace a plate?? that will cost me another $1000. Please explain to me what the problem could be and why it wasn't...


Flex plate, thats the gear that the starter meshes with to turn the engine. if it was noisy and didnt turn the engine every time, the the mechanic would not know this until the starter was out and the "flex plate" gears inspected.

Sep 05, 2010 | 2003 Honda Accord

2 Answers

My 1986 GMC Sierra Classic K1500 4x4 350 engine has problems starting . The starter hits the flywheel or it meshes but can't turn the flywheel over. The starter is new. Would the battery size have anything...


The starter should have come with shims. You may have to adjust the new starter with the shims, so that the bendix, starter drive, meshes properly with the ring gear.
As long as the battery is fully charged it should turn the engine over.
Please let me know what you find.

Feb 11, 2010 | 1986 GMC K1500

2 Answers

Where is tha starter located on a 1998 honda accord


On the 2.3L it is located on the front/radiator side of the engine, near the center of the vehicle (left to right) and is easily visible without removing anything.

On the 3.0L engine it is also on the front/radiator side of the engine, but located further to the driver side, below the battery area.

Oct 17, 2009 | 1998 Honda Accord

2 Answers

Problem with ignition system honda cbr600f


Hi and welcome to FixYa,

Your description could be any of 2 possibilities:
  • starter relay/solenoid; and/or
  • starter motor.
To determine which, jump the 2 big terminals of the starter relay/solenoid when starting the bike; if the motor turns, the relay/solenoid is defective; if the starter motor does not turn, the starter motor is defective (most likely the carbon brushes).

Of course other possibilities still exist, such as:
  • loose, corroded battery terminals, relay, starter terminal/connectors;
  • weak battery.
  • open, corroded fuse/fuse terminals.
Good luck and Thank you for using FixYa. Happy New Year.

Pls be informed that due to my current rank and rating, even a Helpful would be detrimental to my status. Should this solution not address your concern, it would be appreciated if you could just not rate this at all. Cheers.

Jan 01, 2009 | 1997 Honda CBR 600 F(3)V

Not finding what you are looking for?
2006 Honda CBF 250 Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...