Question about Pit Bike 125cc 4 Stroke Dirt Bike

2 Answers

Lifan 140 crank broke were fly wheel is - Pit Bike 125cc 4 Stroke Dirt Bike

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 24 Answers

When pulling flywheels and such, use the appropriate pullers. Some work like a screw on the inside of rotor and directly push on crank end. Some rotors have tapped holes on face to attach a puller that allso pushes directly on crank end. Eather way the end of the crank won't break, and the rotor itself stands a better chance to survive. And it will be a whole lot easier

Posted on Jul 09, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 180 Answers

Pull the motor split the cases and replace the crankshaft.
Or buy another motor.

That is a tappered an keyed shaft, that holds the rotor/flywwheel.
I've only saw that happen when someone was beating on the rotor to try to remove it.

They use junk metal these days and with the right amount of pressure from prying off the rotor could break the cranckshaft there.

Not sure what your question is but as i mentioned above the sloutions for this.

Posted on Dec 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camshaft and crankshaft timing allinment marks


I don't think they put the timing marks on the main crank shaft front fly wheel any more, since they no longer have distributers. Take out your #1 cylinder spark plug and hand turn your engine crank until the piston is at top dead center, then make your own mark on the fly wheel....I don't think there is a mark any more, unless you have and older car with a distributer....if so...look down on your fly wheel....center front engine about 5/8 of the way down fro the top of your engine. Good luck...be careful.

Mar 27, 2015 | Cars & Trucks

1 Answer

What causes starter housing to break near the fly wheel of John deere tractor 2950?


The starter armature may have been stuck while engaged with the flywheel or possibly just a casting that failed.

Mar 03, 2015 | John Deere Garden

1 Answer

How to install a magneto part#610759 on a 12 hp Tecumseh engine #143.622022


loosen the nut on the crank use a peace of (BRASS) put it on
the end and hit it the fly wheel will come off and most mags
just bolt on the fly wheel has a key way line it up and push
the fly wheel back on and tighten the nut done deal

Sep 16, 2014 | Garden

1 Answer

What forr sale Looking for a yx 140?


Fixya doesn't sell anything,sorry!

Jul 19, 2014 | eBay Selling

1 Answer

2000 olds alero cranks then makes a metal grinding sound and won't start


You need to have your flywheel: replaced.Your starter motor engages against the fly wheel at the back of the motor. Every time your motor stops it tends to be in the same few positions (just the way things work) so there is more stress on some parts of your fly wheel than others. Because of this the teeth wear out on the fly wheel which means the starter can correctly engage on the fly wheel which is the grinding noise.

Jan 18, 2013 | 2000 Oldsmobile Alero

1 Answer

My car wont start. There is power to the car but I hear a clicking noise when I try to crank it.


Fly wheel may have teeth that broke off pull the starter look for chew marks.

Nov 04, 2011 | 2001 Mercury Cougar

1 Answer

I cannot get the timing marks on Crank and fly wheel alinged


to be honest it not as easy as it sounds to line them both up,,,,you may need to use a locking stud to do this,, and i have seen engines that just wont line up even to half a tooth out,,, but they run just fine anyhow, its all down to just how good the pullys were cut and marked

Feb 16, 2010 | 1994 Volkswagen Jetta

Not finding what you are looking for?
Pit Bike 125cc 4 Stroke Dirt Bike Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pit Experts

micky dee

Level 3 Expert

2720 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

40632 Answers

shuyumeng
shuyumeng

Level 3 Expert

951 Answers

Are you a Pit Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...