Question about 1987 Honda CBR 1000 F

Open Question

How to replace timming chain on 1988 cbr1000 - 1987 Honda CBR 1000 F

Posted by on

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1978 Answers

SOURCE: what type engine oil does an 1988 cbr1000 take

You can use any oil that is JASO MA certified motorcycle oil. 10w-40 for cold climate/year round. 20w-50 for warm climate/touring. Automotive oils use different additives and may cause scoring in certain types of cam bearings. Do not use any oil that says " Energy Conserving " on the label . It will shorten the life of your wet clutch and transmission gears. If you choose Synthetic oils, they will help your bike run cooler and shift easier. Shell Rotella T ($12 a gallon ) and Rotella T Synthetic 15w-40 ($22 a gallon) are inexpensive JASO MA oils. You will need 4 quarts of oil, an aluminum drain plug washer, and a filter. Pour in 3.4 quarts , run the motor, and check the oil level . Top up as needed.

Posted on Jun 05, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced timming chain now does want to run correctly bad fumes

It sounds like the timing chain was replaced one tooth off. The only other option if the timing chain is correct would be to adjust the ignition timing. Since the timing chain was replaced I would think it to be the first problem.

Dec 17, 2013 | Cars & Trucks

1 Answer

Timing case cover assembly

Hi Tim,here's a link on how to remove timing chain cover.

Mar 31, 2013 | 1988 Oldsmobile Cutlass Ciera

1 Answer

I have a 1988 jeep cherokee pioneer with a inline 6 somthing in the timming is off what could be the problem if you cant adjust the timming on them

1st of all be sure to read the manufacturers information under your hood about the procedure of adjusting the timing on your jeep, afterwards, you will need a timing light to do this procedure, and if the adjustment of the timing doesn't want to stay in place, after it is set, then it could be your timing chain has an a certain amount of slack in it due to wear, 1st of all how many miles is on the jeep, if it is very high mileage, this could be the problem causing the slack, and the timing not staying in it's proper setting. if this is your problem, then the timing chain will have to be replaced.

Mar 07, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

When should you replace tha timming chain 2006 armada??

you will probably find that a timing chain is in the engine for the life of the engine or until it needs to be replaced,

May 17, 2010 | Cars & Trucks

1 Answer

Timming problems for 88 toyota 4runner

could be the valves try adjusting them and set the timing by crossing over the ignition terminals behind the battry there is a little black box with atop that comes of look in the book for the actual termilal numbers is about 4 of them. hope this helps

Dec 01, 2009 | 1988 Toyota 4Runner

1 Answer

Replaced timming chain. engine wont start

be sure timing marks are lined up

Jul 28, 2009 | 1988 Toyota Pickup

1 Answer

88 chevy 350 knocking or pinging near front of engine

Just for the heck of it, have you tried upiing the gasoline one grade?

Jun 15, 2009 | 1988 Chevrolet C1500

1 Answer

How do you change the back tire on a 1988 honda shadow 600 vlx ??

you don't have a centerstand so you'll need a racestand or ATV jack to raise your bike up off the floor..Disconnect rear brake linkage, unbolt and remove axle, roll tire forward a couple inches and remove chain from rr sprocket, have tire fixed or replaced..reinstall is opposite of removal...Good Luck to you friend....Tim

Apr 28, 2009 | 1988 Honda VT 1100 C Shadow

2 Answers

87 mazda b2200

if it wont hold an idle then one or more of the cylinders are probably too low or high in compression and if it's backfireing then the ignition timming could be off. I would take a compressin test of all cylenders and if they are all in range I would hook up a timming light to se if the timming is out

Jul 02, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
1987 Honda CBR 1000 F Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides