Question about Harley Davidson FLSTF Fat boy Motorcycles

1 Answer

MY FATBOY FELL OVER AND THE FRONT-END IS NOW OUT OF LINE. HOW DO I STRAIGHTEN IT? NEEDS TO BE TURNED A BIT COUNTERCLOCKWISE.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Look on the backside of the lower triple tree. There should be a bolt on each side of the triple tree. Loosen these bolts and and put the front TIRE against a wall in the same direction you want to twist the front end. Twist the front end using the handlebars. When you get it straight, tighten the bolts to 30 foot pounds torque.

Good Luck
Steve

Posted on Oct 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bike hit a pothole and was dropped. Handlebars now a bit out of line. How can I adjust them? Thanks


Get a steel tube slide it over the end of the bent handle bar and lever it to straighten it out

Feb 13, 2015 | 2005 Piaggio Zip 50

1 Answer

How do you replace the o-ring on the gas vapor line on a ******* zero turn?


I could be wrong, but I deal with internal o rings all the time, for cars. Get a paper clip, straighten it out, file down one end kind of sharp. Put a small (1/8 inch) bend on both ends. Use the sharp end to remove the O ring. use the dull end to push and pull it back into it's slot. Put the O ring in. Push that end past the slot, until the front of it come to the slot. Push the front into the slot and start pulling the rest of the o ring and pushing in the slot at the same time. Best way I found to do it. And it will go...

Sep 05, 2014 | Cars & Trucks

1 Answer

Steering wheel doesnt come back while driving


try greasing the front end . needs a lube job,perhaps see an alignment shop to check front end

Jun 28, 2013 | Honda Civic Cars & Trucks

1 Answer

Front passenger side 'clicking' noise?


no brake problem as it is not there when on jacks
most clicks are failing cv joints are are normally when going slow and on a bit of a turn
Take it to a drive line specialist shop for a proper diagnosis

Apr 12, 2017 | Mazda MAZDASPEED3 Cars & Trucks

1 Answer

No Ice. Replaced 4 solenoid water inlet valves. Icemaker spins around, but no water comes up. Any ideas?? Bruce


Follow the water source line on the back of the refrigerator to the shutoffvalve on the water supply. Turn the shutoff valve counterclockwise to open itfully. Inspect the water source line for kinks. Straighten the line to removekinks.Confirm water flows to solenoid one end. And also check freezer door is closed as it will sense solenoid to open to water flow into ice maker. Sometimes, water flow might be plugged by frosting. Check freezer setting temp 5 degree. Thanks.

Jan 29, 2011 | GE Profile PDS22MHR Bottom Freezer...

2 Answers

Vaccum line fell off rear end not sure where it belongs


the vent tube for the ring and pinion housing is the only tubing made of rubber for the axle

Feb 14, 2010 | 1997 Dodge Ram 2500 Club Cab

1 Answer

How do you open a door that is locked and closed on a 74 convertalble beetle. the lock can not be be pulled manually or turned with the key


you need to use a coat hanget to relase it with butthis needs some practice or you can call a lock smith or tow truck to come and open it if you have towing avalible and once it is open remove the inside pannel and straighten out the rod so it will lock and unlock. You may have to replace the plastic tap that holds it in place if it fell off.

Jul 16, 2009 | 2002 Volkswagen Beetle Turbo S

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...