Question about 1983 Honda GL 1100 Innerstate Gold Wing
1983 gl1100i won't start has compression spark wants to start but won't checked belts timing replace the spark igniters battery good what am I missing? The bike ran broke belt replaced valves adjusted them, timed the motor, turns over wants to fire off but doesn't
Hi, Jooe_hardy and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
14. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
15. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
16. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
17. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
18. Faulty neutral, clutch lever, or kickstand safety switch.
19. Faulty fuel pump or fuse or relay.
20. A stuck bent or burnt valve.
21. Tilt sensor needs a reset.
22. Security system not disarming alarm needs a reset.
23. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
GL1100 won start just clicks
Bike Will Not Start GL1100 Information Questions goldwingdocs com
Honda GoldWing GL1100 Service Manual
Honda Gold Wing GL1100 Owner Manual
Posted on Jun 30, 2017
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
When I recently ordered parts from Saber Cycle, they included a piece of information that pertained to my motorcycle, which is also a 1983 Honda Goldwing GL1100 Interstate. Here is what it says, I hope this helps:
Air Cut-Off Valve
The air cut-off valve is an extremely important part of the fuel/air intake system that is frequently missed even my competent mechanics, most of whom are not even aware of its existence or how it functions.
Every GL1000 has one, located in the air intake tube, between the air cleaner box and the manifold. Every GL1100 has four, located in the top air intake passage of each carburetor, and every GL1200 has one located in the plenum box below the air cleaner box similar to the GL1000.
These valves are "air blockers", along with the carburetor o-rings, serving to restrict air flow and increase the fuel/air mixture ratio when the carb slides are in the lower RPM range, up to closed so that the machine will start and idle smoothly with virtually no choking and accelerate rapidly, with no stumble or hesitation.
When typical starting requires heavy and prolonged choking to keep the bike running, when stalling and hesitation occurs even while "warmed up" and when backfiring pops while the throttle is shut off while cruising, most people will start fooling with the air screws to try to overcome the problem, only making it worse along with reducing their gas mileage.
Running with dysfunctional air cut-off valves can causes severe engine damage or failure. When the valves are dysfunctional, the engine pulls nearly total air in the low RPM range through the carbs and on to the combustion chamber. The fuel/air ratio is extremely poor with pre-ignition long before the normal 38 to 40 degree firing point, generating an enormous amount of heat, with no power, which is trapped a longer period of time in the cylinder before the exhaust valve opens.
This heat goes mostly up through the cylinder head, gradually incinerating the head gaskets and allowing engine coolant (anti-freeze) to seep into the engine. You can easily spot when you are in trouble by a puff of bluish-white or white smoke on first starting the engine. Don't leave it alone. Change head gaskets immediately or you could take out your bottom end bearings, ruining the engine.
For those of you installing new exhaust systems, you will discolor your headpipes, either blue (lean state) or gold (rich state). You can destain your pipes using "blueaway" or "blue-off" but be careful not to rub the chrome, just dab gently.k These compounds are usually purchased at a Harley dealer or Harley oriented aftermarket shop.
Honda genuine pipes, like many Yamaha pipes, have a double wall for a portion of the headpipe which masks this discoloration-but also masks a bad state of tune. Even if your pipes are original and still in good shape, don't think that you are OK if the bike has any or all of the dysfunctional air cut-off valve running and performance characteristics.
If your 1975 to 1987 Gold Wing is not getting 50-58 miles per gallon (20-23 KM/Liter), you have one of the most obvious signs of trouble. It is likely your air screws have been backed out to try overcome the effects of the poor running, stumbling, starting and stalling and quitting.
Resynchronize all four carbs to the #3 carb vacuum level using mercury carb sticks or vacuum dial gauges. Stay with strict use of the setting levels in either the Honda, Clymer or Haynes manuals. Do not attempt to tune any other way! Guessing will not work and can cause considerable engine damage!!!
Posted on Sep 26, 2009
Tips for a great answer:
Aug 07, 2014 | 1983 Honda GL 1100 Gold Wing
Jun 27, 2014 | 1982 Honda GL 1100 Gold Wing
May 04, 2013 | 1983 Honda GL 1100 Innerstate Gold Wing
Apr 02, 2013 | 1983 Honda GL 1100 Gold Wing
Aug 18, 2012 | 1982 Honda GL 1100 Innerstate Gold Wing
May 29, 2012 | 1983 Honda GL 1100 Innerstate Gold Wing
Jul 31, 2010 | 1983 Honda GL 1100 Innerstate Gold Wing
May 24, 2010 | 1983 Honda GL 1100 Innerstate Gold Wing
May 12, 2010 | 1983 Honda GL 1100 Innerstate Gold Wing
May 08, 2010 | 1983 Honda GL 1100 Innerstate Gold Wing
Nov 23, 2017 | Motorcycles
Nov 23, 2017 | Motorcycles
Nov 23, 2017 | Motorcycles
76 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: