Question about 1997 Cagiva Mito 125 Evoluzione

1 Answer

Indicators wont flash 3 new relays still wont flash lights either on with no flasing or off but ticking with no lights i have the same problem with 2 bikes

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cagiva Master
  • 39,940 Answers

Hi, Kevandmax before diagnosing any turn signal issue make sure the bulb is good and the light fuse has continuity with a test light. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue, please visit the websites below. Good luck and have a nice day. Indicator doesnt flash it just stays on
http://www.125ccsportsbikes.com/forums/index.php?showtopic=88880
Free Cagiva Motorcycle Service Manuals for download
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Posted on Jan 21, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear brake light wont work and left indicator wont flash i brought new indicator flasher and new battery wot could it be thanks


The rear brake should have a switch about 2 or 3 inches from the rear of the pedal pivot. Any further info is difficult to give without knowing what bike it is?!?!?!

Aug 10, 2013 | Motorcycles

1 Answer

The Security light keeps flasing in my Mazda 3 2010,


Mostly, there's something wrong with the wiring. Why don't you give it once 4 servicing and ask them itself???

Apr 24, 2012 | 2010 Mazda 3 1.6i

1 Answer

Blinkers come on steady rather than flashing. The flasher relay seemed as though it wasn't breaking the current flow to the blinkers, with a constant whine coming from the relay when the blinkers were...


A noise at the relay indicates a short circuit at atleast 1indicator, disconect all the indicators and check if the relay still makes a noise, if it is all quiet plug in the indicators 1at a time select left with the switch turned on and fit each indicator wires in the correct location if noise is emited as 1 indicator is connected you may want to check again with it disconnected. Have you checked that the bulb wattage. Suits that as marked on the flasher relay

Apr 26, 2011 | Honda GL 1000 (K3 Motorcycles

1 Answer

Ps3 shut down wont restart flasing red light


PS3 shut down automatically and leave a flashing red light,
Please read this post, you can find a solution : PS3 Red Light Blinking Fix

Feb 01, 2011 | Sony Playstation 3 (PS3) Console

1 Answer

My split system starts and in 2 min turns of and


Hi, the Led lights do indicate a problem with the unit. Not knowing what the flashes are, and you can find out what they mean, you will need to find the chart either on the indoor unit behind the cover by this Led light on the circuit board or could be on the outdoor unit panel. This chart will have error codes listed on it and according to how many flashes are taking place or if they are long slow or fast ect., such as this example, 3 flashes stops for a min and flashes 3 times again. It will lead you down the numbered chart to find this, like33 or 3-3 ect. This will tell you what is going on. Check this out and get back to me. If you have the manual, it should tell you. I will check back tomorrow to see what you have found, so contact me.
Shastalaker7

Dec 19, 2009 | Heating & Cooling

1 Answer

Flasing red light xbox360


get the number for microsoft and get a free refund thats what i did

Oct 26, 2009 | Video Game Consoles & Games

1 Answer

Brother HL 5250 red light flashing


I found this solution on the web-- Hope it helps.

The HL-2070N gets stuck in a toner end-of-life error condition. Perform the following to clear :
With paper loaded, new toner in,

Open front door
Turn off printer
While holding down the GO button, turn printer back on
When all four LEDs light up release GO button. All LEDs will turn off
Press the GO button 2 times. The 3 LEDs (toner, drum, paper) will light up solid
Press the GO button 5 times
Paper light will be blinking
At this point the toner end-of-life condition has been reset. Close front door.
BTW, I got this from Brother Support. Also, just a reminder, timing is important here so don't pause between button presses.

Jan 28, 2009 | Brother HL-2070N Laser Printer

1 Answer

LG split system air conditionsr


3 flases indicates a communication error. Have a technician check wiring and connections.

Jun 05, 2007 | LG LSC121PMA Split System Air Conditioner

Not finding what you are looking for?
1997 Cagiva Mito 125 Evoluzione Logo

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cagiva Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Steve P
Steve P

Level 3 Expert

2503 Answers

Are you a Cagiva Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...