Question about 2005 Harley Davidson FXDL - FXDLI Dyna Low Rider

1 Answer

Fluid levels. all - 2005 Harley Davidson FXDL - FXDLI Dyna Low Rider

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Enigne oil - The dipstick is on the corner of the transmission as the oil tank is on the bottom of the transmission. The dipstick has two marks on it. The upper mark is "FULL HOT", and the lower mark is "FULL COLD". Keep the oil level between the two marks when you check the oil with the bike on the sidestand.

Primary - Remove the derby cover and stand the bike straight up. The out cluch basket is made out of bright aluminum. Just inside is a dark colored round piece of metal. This is the clutch spring. The oil should be just to the bottom of this spring at it's lowest point. Do not overfill as it will cause the clutch to drag.

Transmission - On the right hand side of the bike on the end of the transmission is the clutch release mechanism. It is just behind the exhaust pipes and the clutch cable runs into it. On top of this cover, there's a plug that takes a 3/8" Allen or hex key to remove. Remove the plug and there's a dipstick on it. Keep the oil level between the two lines. Check the fluid level with the bike standing straight up.

Good Luck
steve

Posted on Oct 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Buick LeSabre power steering dip stick. Where is it?


The power steering fluid level is indicated by marks on a fluid level indicator. The fluid level indicator is located on the fluid reservoir cap. Inspect the fluid level when the engine compartment is cool. Ensure that the fluid level is at the FULL COLD mark. When the engine compartment is hot, ensure that the fluid level is at the HOT mark.

Located on back side of engine below the alternator

Feb 08, 2017 | 2000 Buick LeSabre

3 Answers

Just got 1996 chevy cavalier. Where do you add transmission fluid?


the transmission fluid goes down the dip stick hole ,either use a small funnel or special tranny fluid refill top up bottle

Feb 04, 2011 | 1996 Chevrolet Cavalier

1 Answer

How much trannyfluid goes in a 99 gmc sonoma


5 QUARTS FOR FLUID FILTER CHANGE. IF REPLACING TORQUE CONVERTER OR TRANSMISSION OVER HAUL. YOU NEED 13.8 QUARTS. WHEN YOU CHANGE FLUID AND FILTER.BESURE YOU HAVE TRANSMISSION FLUID LEVEL TO THE FULL MARK BEFORE DRIVING VECHICLE.LET ENGINE IDLE UNTIL GET WARM BUT CHECK TRANSMISSION FLUID WHILE ENGINE IDLING.IF FLUID LEVEL DROP A LITTLE ADD A LITTLE MORE TO GET FLUID LEVEL AT FULL MARK.ONCE ENGINE GET OPERATING TEMPERATURE.SHIFT TRANSMISSION THROUGH ALL GEARS TWICE ONE AT A TIME.CHECK TRANSMISSION FLUID LEVEL.SHOULD BE ON FULL MARK.DRIVE VECHICLE FEW MILES CHECK FLUID LEVEL.IF FLUID LEVEL.FULL YOU GOOD.IF STILL LOW ADD A PINT AT A TIME.ONCE FLUID LEVEL CORRECT. SHIFTING OKAY TIME PLAY.YOU GOOD TO GO.

Jan 22, 2011 | 1999 GMC Sonoma

1 Answer

How to check trasmission fluid no dipstick just a red cap


4T40E Automatic Transaxle CAUTION
Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of the transaxle fluid to exhaust pipe. The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
  1. The fluid level should be checked when the transaxle is near room temperature or at 104°F (40°C). To acquire this, left the car idle for 3-5 minutes with all of the accessories off. Fig. 5: Location of the fluid level screw and the fill/vent cap needed to check the fluid for the 4T40E automatic transaxle 87951085.gif

  2. Apply the brake, then move the gear shift selector through all gear ranges, pausing three seconds in each range. Shift the lever into P.
  3. Raise and safely support the vehicle.
  4. Place a suitable drain pan under the check plug to catch any fluid that may drip out.
  5. Remove the oil check plug. The oil level should be at the bottom of the oil check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the screw hole when the screw is removed.
  6. If fluid drains through the screw hole, the transaxle may have been overfilled. When fluid stops draining, then fluid level is correct and the check plug may be installed. If fluid does not drain through the screw hole, the transaxle fluid may have been low. Add fluid at the vent cap location in 1 pint increments until the oil level is at the bottom of the oil check hole.
  7. Install the oil check plug/fluid level screw and tighten to 10 ft. lbs. (14 Nm).
  8. Carefully lower the vehicle.
prev.gif next.gif

Jan 21, 2011 | 1997 Pontiac Sunfire

1 Answer

Need easy way to take off transmission fluid cap.Trying to check fluid.


Hello Eddie.

Checking the fluid level on these cars isn't easy. Not one of the Generals best ideas. There isn't a dipstick under that cap. The fluid level is checked by removing a screw on the side of the transmission while the car is running and sitting level.
This makes it tricky to do for the average do-it-yourselfer as you not only need to jack up the front of the car but the back end to keep it level. Probably a vain attempt to get the cars back into the dealers shop.

Anyway, here is the book procedure.

kiltylake_16.gif

kiltylake_17.gif


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect

The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  1. Install fluid level screw. Tighten 12 N.m (106 lb in)
  2. Lower vehicle.
I hope this helps you along.
Thank you for using FixYa.

KL

Nov 19, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Check automatic transmission fluid level 2004 Pontiac grand am


TRANSAXLE FLUID CHECKING PROCEDURE



The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect
The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park.
Important: Vehicle must be kept level on the hoist.

  1. Raise vehicle on hoist.
  2. Place oil container under fluid level screw.
  3. Remove the fluid level screw with the engine running at idle.
  4. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  5. Install fluid level screw.
Tighten 12 Nm (106 lb. in.)

  1. Lower vehicle.
  2. Shut off engine.
Adding Transaxle Fluid:

With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.

  1. Install fluid level screw.
Tighten 12 Nm (106 lb. in.)

  1. Lower vehicle.

Oct 20, 2010 | 2004 Pontiac Grand Am

1 Answer

I have a 2000 chevy cavalier Z24 and it seems to not have a dipstick to check transmission fluid how do you tell when it is low or does anyone know where it is


Let vehicle idle for three to five minutes with accessories off. Apply brake Move shift lever through all gear ranges, pausing three seconds in each range. Place shift lever in Park. Important: Vehicle must be kept level on the hoist. Raise vehicle on hoist. Place oil container under fluid level screw. it is near the bottom of the driveshaft Remove the fluid level screw with the engine running at idle. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap 1 PINT Increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. Install fluid level screw. Tighten

Jun 12, 2009 | 2000 Chevrolet Cavalier

1 Answer

No tranny dipstick to be found ANYWHERE!!!!!!!!!


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid. Inspect The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) . CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe. The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid. WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole. 1. Let vehicle idle for three to five minutes with accessories off. 2. Apply brake 3. Move shift lever through all gear ranges, pausing three seconds in each range. 4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist. 5. Raise vehicle on hoist. 6. Place oil container under fluid level screw. 7. Remove the fluid level screw with the engine running at idle. 8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID. 9. Install fluid level screw. Tighten 12 N.m (106 lb in) 10. Lower vehicle. 11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. 1. Install fluid level screw. Tighten 12 N.m (106 lb in) 2. Lower vehicle.

Jun 05, 2009 | 2004 Chevrolet Malibu

2 Answers

Location of transmission (automatic) dipstick


You DO NOT have one.

There is a small bolt/plug in the transmission above the pan that needs to be removed. The fluid will run out if it's overfilled. The transmission needs to be at room temperature or a little warmer to check the level.


The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.
Inspect:
The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F).
CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.
The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.
WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine.
181efc6.gif
Adding Transaxle Fluid:
  1. With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  2. Install fluid level screw. Tighten 12 N.m (106 lb in)
  3. Lower vehicle
0e45832.gif

Mar 23, 2009 | 1996 Chevrolet Cavalier

1 Answer

Where do I check the transmission fluid on a 1997 Hyundai excel


Remove Transmission Fluid Level Check
Locate and remove the transmission fluid level checker, in most cars and trucks this is where the fluid is checked and added.
1687565.jpg
Insert fluid funnel and add transmission fluid until the proper amount of fluid level is reached. Let engine warm and recheck fluid level, add fluid as needed. Do not over fill the transmission, it could foam the fluid and cause low fluid pressure causing premature transmission failure. recheck transmission for leaks and recheck fluid level in a couple of days.

DIAGNOSIS AND TEST FLUID LEVEL AND CONDITION
1. Park the vehicle on a level surface. 2. Before removing the dipstick, wipe all dirt from the area around the dipstick. 3. With the selector lever in "P" (Park) and the parking brake applied, start the engine. 4. The engine should be running at idle speed and the fluid should be at normal operating temperature [80-90°C (176-194°F)]. 5. Move the selector lever to every position to fill the torque converter and hydraulic circuit with fluid, then place the lever in the "N" (Neutral) position. This operation checks that fluid level check is accurate. 6. Check if the fluid level is in the "HOT" range shown on the dipstick. If the fluid is low, add automatic transaxle fluid until the level reaches the "HOT" range.
ab7f169.gif

Aug 13, 2008 | Hyundai Excel Cars & Trucks

Not finding what you are looking for?
2005 Harley Davidson FXDL - FXDLI Dyna Low Rider Logo

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...