Starter - 2006 Mazda 3

hot wire starter you can short out ignition switch and wiring. to jump starter ignition switch start postion.you have to run 10 gauge jumper wire from the starter solenoid positive battery terminal to starter switch or S terminal on starter solenoid this procedure take two people but better remove starter replace starter solenoid. trying jumping off starter on camaro would be dangerous you have jack up car to get to starter and wiring person laying under car hot wiring starter while other person hold ignition start position put person under car in deadly position just remove starter have auto parts check it out first replace starter or solenoid if either bad. easier hot wire starter if starter under hood like my 1977 vega monza had starter at top could take long screw driver jump starter off.on the four cylinders engines back in the 70s. camaro starter under car dangerous trying to hot wire not a good idea.

Its located in the under hood engine compartment fuse box.

There will be three same relays.One for fuel pump and other for horn and bit bigger one for starter controlling.

For more help regarding starter

CAR STARTER REMOVAL? TESTING

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

-----------

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

How to replace Starter on Infiniti Q45?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------

2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----

Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

CAR STARTER REMOVAL? TESTING

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----

How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html ----------- How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------
How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------
2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----
Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============
For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----
These help links will help.
Click the link below:-----

How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html----------- How to replace starter in car? http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html
-----------How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html
---------- 2006 GM Montana: How to replace Starter Solenoid? http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html
-----Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?
http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html
----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------
Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?
------------These details will help.Thanks.

STARTING SYSTEM Starter REMOVAL & INSTALLATION Fig. 1: Disconnect the wiring from the starter motor
Fig. 2: After unbolting the starter, remove it from the vehicle
In 1978, a gear reduction starter was introduced on some Canadian and United States models. The differences between the gear reduction and conventional starters are: the gear reduction starter has a set of ratio reduction gears while the conventional starter does not. The extra gears on the gear reduction starter make the starter pinion gear turn at about half the speed of the starter, giving the starter twice the turning power of a conventional starter.

1. Disconnect the negative battery cable from the battery.
2. Tag and disconnect the wiring at the starter, taking note of the positions for correct reinstallation.
3. Remove the bolts attaching the starter to the engine and remove the starter from the vehicle.
4. Install the starter in the reverse order of removal.

REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown
Fig. 2: Remove the starter electrical connections from the back of the starter
Fig. 3: Remove the three bell-housing cover retaining bolts and . . .
Fig. 4: . . . remove the bell-housing cover
Fig. 5: Remove the starter support brace-to-engine bolt
Fig. 6: The starter is retained by two bolts
Fig. 7: Remove the bolts and . . .
Fig. 8: . . . remove the starter from the engine
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside

1. Disconnect the negative battery cable at the battery.
2. Raise and safely support the vehicle.
3. Remove the electrical connections from the back of the starter.
4. Remove the bell-housing cover.
5. Remove the starter support bracket bolt from the engine block.
6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
   
8. Transfer the starter support bracket to the new starter if the starter is being replaced.
9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
11. Install the bell-housing cover.
12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
13. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines

1. Disconnect the negative battery cable at the battery.
2. Detach the air inlet duct from the throttle body.
3. Remove the top starter bolt.
4. Raise and safely support the vehicle.
5. Remove the lower starter retaining bolt.
6. If necessary, position the engine wiring harness aside.
7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
8. Remove the starter from the vehicle. To install:
   
9. Raise the starter to the vehicle, then attach the wiring.
10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
11. If moved, reposition the engine wiring harness.
12. Carefully lower the vehicle.
13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
14. Fasten the air inlet duct to the throttle body.
15. Connect the negative battery cable.

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

To install:

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1.6L, 1.8L & 2.0L Engines

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1.8L & 2.0L Engines

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

2.4L & 2.5L Engines

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

2.4L Engine

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine
   

continue...

Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--


4-cylinder engine starter connections

1. Disconnect the negative battery cable.
   
2. Raise and safely support the vehicle on jackstands.
   
3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
   
4. Tag and disconnect the starter battery and control wiring at the starter.
   
5. If equipped, remove the starter bracket and/or heat shield.
   
6. Remove the starter-to-engine bolts.
   
7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
   

To install:

1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
   
2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
   
3. Install the starter bracket and/or heat shield, if equipped.
   
4. Connect the battery and starter control electrical wires to the starter.
   
5. If the EGR pipe was removed, install it.
   
6. Lower the vehicle.
   
7. Connect the negative battery cable.
   
8. Start the vehicle to make sure the starter functions correctly.
   

This is for the V6 motor--


6-cylinder engine starter installation

1. Disconnect the negative battery cable.
   
2. Raise and safely support the vehicle on jackstands.
   
3. Label and disconnect the battery and starter control wires from the starter.
   
4. If equipped, remove the starter bracket and/or heat shield.
   
5. Remove the starter-to-engine mounting bolts.
   
6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
   

To install:

1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
   
2. Install the starter bracket and/or heat shield, if equipped.
   
3. Reconnect the electrical connectors to the starter.
   
4. Lower the vehicle.
   
5. Connect the negative battery cable.
   
6. Start the vehicle to make sure the starter functions correctly.
   

1. Disconnect the negative battery cable at the battery.
2. Raise and safely support the vehicle.
3. Remove the electrical connections from the back of the starter.
4. Remove the bell-housing cover.
5. Remove the starter support bracket bolt from the engine block.
6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
7. Remove the nuts/bolts that hold the starter support bracket to the starter.

To install:

1. Transfer the starter support bracket to the new starter if the starter is being replaced.
2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
4. Install the bell-housing cover.
5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
6. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines
See Figure 10