Question about 2003 Suzuki RM 125

1 Answer

HOW DO YOU TAKE THE ROD OFF - 2003 Suzuki RM 125

Posted by on

  • yadayada
    yadayada Sep 28, 2010

    what rod do u refer to?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

You have to split the crank.It has to be pressed apart. Then press back together.Hope this helps
D.

Posted on Sep 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

How do i loosen the outer tie rod end to remove it from the bushing once tie rod is out of streeing knuckle i know it will need to be aligined and i need to count treads when putting new outer tie rod end...


You may need a propane torch to heat up the nut on end of outer tie rod. With tie rod still attached to steering knuckle try to loosen the outer tie rod end nut that is connected to inner tie rod. Pull tie rod end back out of knuckle. Use pliers or vise grips to hold inner tie rod end while turning outer tie rod end to the left.

Oct 27, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

How do you remove the tie rod from a 2000 dodge caravan


Depending on inside or outside tie-rod i'll go over both. Outside tie rod step: 1:Jack vehicle and remove tire
2:Loosen jam nut on tie rod, this is the nut directly behind the tie-rod.
3:remove cotter-pin on castle nut of tie-rod,remove nut.
4:turn the wheel completely to the extended side so that the tie rod is stretching out and you can get at it with a hammer. If doing driver-side turn wheel all the way to right.
5:Hit the nub that the tie rod is bolted to not the tie rod it will take some swinging. but you'll know when you have broken it free it will pop right out.
6:marking a spot on the shaft that the tie rod is on or leaving the existing jam nut as a marker to thread the new tie rod on. this can effect your alignment angle.
7:using a wrench or vise grip thread the tie rod off and the new one on.
8:Put new tie rod on and bolt down.
9:dont forget to install cotter pin good luck.


Apr 07, 2010 | 2000 Dodge Caravan

2 Answers

2000 LINCOLN LS - Outer tie rod removal assistance


Yes degreaser will not hurt it. The outer tie rod is retained only by one nut that connects it to the inner tie rod.Once you have this loosen just turn the outer tie rod to the left to remove it from the inner tie rod.

Feb 24, 2010 | 2000 Lincoln LS

1 Answer

How to install tie rods on a 1993 del sol


Instructions Things You'll Need:
  • Lug nut wrench
  • Jack
  • Jack stands
  • Wrench or pliers
  • Tie rod puller
  • Marker or paint
  • Pen and paper
  • Anti-seize compound
  • Torque wrench
    Remove the Tie Rod End
  1. Step 1 Purchase tie rod ends that are specific to your Honda model and year, for tie rod ends vary from model year to model year. The tie rod ends often come with nuts and cotter pins (glorified bobby pins).
  2. Step 2 Loosen the lug nuts on the front tires, but don't remove them. Jack up your vehicle, then support it securely on jack stands. Remove the tires.
  3. Step 3 Use a wrench or piers to loosen the outer tie rod's locking nut, but do so by only 1/8th of a turn. Mark the tie rod end's position on the threaded portion of the tie rod with paint or a marker.
  4. Step 4 Take out the cotter pin or key and use a wrench or pliers to loosen and remove the castellated nut from the outer tie rod end's spindle.
  5. Step 5 Separate the tie rod and the steering knuckle with a tie rod puller.
  6. Step 6 Grasp the tie rod with a wrench while you screw off the tie rod end. Make sure you keep track of the number of turns it takes to remove it, and write that number down. It'll help you when you install the replacement tie rod end.
    Replace the Tie Rod End
  7. Step 1 Put a coat of anti-seize compound on the threaded portion of the tie rod end, and screw on the lock nut for the tie rod end.
  8. Step 2 Screw on the tie rod end, making sure you do it in the same number of turns as it took to remove the original tie rod end (see Section One, Step 6).
  9. Step 3 Slip the tapered end of the tie rod end into the steering knuckle and tighten the castellated nut to 29 to 35 foot pounds. If your tie rod end doesn't come with a castellated nut, tighten that nut to 32 foot pounds.
  10. Step 4 Install the new cotter pin and tighten the tie rod end's lock nut. Repeat Sections 1 and 2 for the other tie rod end.
  11. Step 5 Reinstall the tires, tighten the lug nuts and get the Honda aligned.

Oct 28, 2009 | 1994 Honda Civic Del Sol

1 Answer

I'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.


1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

May 21, 2009 | 2000 Isuzu Rodeo

4 Answers

2001 Dodge Caravan outer tie rod how to install it macking noice and shold i change stiblizar too


loosen nut on tie rod..22mm wrench,remove nut from tie rod end..18mm socket,hit side of knuckle with hammer to seperate tie rod end..unscrew tie rod end from tie rod..reverse procedure to install..you will to hold down on tie rod end to keep stud from spinning

Mar 16, 2009 | 2001 Dodge Caravan

Not finding what you are looking for?
2003 Suzuki RM 125 Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...