Question about 1990 Honda GL 1500 Gold Wing

1 Answer

How do I remove the carbs - 1990 Honda GL 1500 Gold Wing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

If you do not have a manual I would invest in 1. This is a tough job & I`ve done several.It would be very hard for me to explain how to do it.The manual will help you with ever step with pic`s.Hope this helps you out.
D.

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove carb


Remove air cleaner Remove torx screws in carburetor throat. Remove air cleaner backing plate. Turn off gas valve. Remove fuel line from carb. Pull carb from manifold. Release throttle cables. When re installing carb backing plate, put Loctite Blue on torx screw threads.

Sep 25, 2013 | Harley Davidson FXSTS - FXSTSI Springer...

1 Answer

How do I clean the carborator?


Remove carb from mower. Use carb cleaner and small acid brush to clean outside of carb. Remove bowl from bottom of carb. Clean bowl. Observe bolt that held carb bowl to carb, see if it has a hole or holes thru it. Clean out holes with bread wrapper wire with about 1in of wire. Test float, float down fuel flow, float up fuel stops. Use bread wrapper to clean center port of carb from bottom up thru carb body. Remove float pin float and meter needle, use bread wrapper to clean meter needle passage up thru carb body. Re-assemble carb.
Honda carbs can be purchased new for $14 - $27.

Aug 14, 2013 | Garden

1 Answer

How to remove carburetor from 235 husqvarna chain saw


Start by removing the 3 anti vib spring screws, one on the front underside of the saw, one at the rear underside of the saw, and one at the r/h side of the cylinder, remove the 3 screws holding the l/h side of the rear handle and remove the plastic trigger and throttle lock, the handle and spine will now come away as an assembly from the rest of the saw, now remove the screw at the top r/h side of the saw and remove the square orange plastic plate, once removed you will gain acess to the two 8mm nuts under the air filter securing the carb, there is also one torq screw to remove before the carb and filter bacl plate can be removed, you will also have to pull some of the fuel hoses from the carb to completly remove it.

Dec 23, 2012 | Garden

1 Answer

How to remove the carb from a 2006 Yamaha pw80


pw 80 small kids crosser

look at this


http://www.pwonly.com/schematics/pw50_pics/carb.jpg


the 50 and 80 are praticaly the same carb look at the picture nut and bolt
22 and 23 they remove the carb from the engine

u may have to remove the air box or at least the rubber joiner if there is one i expect there is so u can pull the carb out of the engine

and once removed there will be cables for throtle and choke u must remove the top of the carb to unclip the cables they can be fiddly a oil pipe inportant remember where it goes and remember to fit it back on when the carb goes on

it would not be good if u forget

best of luck if :)

Oct 30, 2012 | Yamaha Motorcycles

1 Answer

Fuel not getting to carb


remove carb...remove float and float jet...blow through with compressed air. Check float height and also check float for holes.

Sep 22, 2012 | Honda Motorcycles

1 Answer

My husqvarna 455 rancher needs a carburetor kit how do you remove the carb


This is not so easy to explain, this is an X Torque engine so the carb does not come off so easy, there are air tubes on the back of the carb, however, remove the air filter, remove the earth cut out wire and earth return wire from the red switch, they are just push on, there is a blue clip on the throttle shaft side of the carb, gently pull out and twist ( this holds the throttle push rod into the carb ), open the throttle trigger with your finger at the same time now remove the throttle push rod from the throttle shaft, once out of the carb pull the rod toward the front of the saw and out of the tank, now unscrew the four allen headed screws from the air filter housing, and remove, ease the carb up and away far enough to remove the fuel hose, now remove completely.

Feb 18, 2012 | Husqvarna Garden

1 Answer

How do I remove carb from 98 honda cr 125? Everything seems to be in the way not sure what to take off to get to it


remove airfilter , loosen airbox then undo both clips either side of carb , remove fuel pipe , tilt carb towards you so you can remove the cable and throttle slide and put to the side hanging ! press the rear tube between airbox and carb , soft , then pull carb out !! pictures or vidio as you start ! P...

Oct 03, 2011 | 2002 Honda CR 125 R

1 Answer

How do i remove the carbs from the engine?


After removing the tank and airbox, loosen the clamp screws securing each carb to the inlet stubs, these can be sometimes difficult to get at and time consuming, also unclip the idle screw from its bracket, remove the choke cable and throttle cable-s from the carbs, some models have water pipes fitted 1on each side of the bank of carbs, once removed have a screw ready to push into the pipe to stop the coolant leaking, if you have difficulty undoing the screws securing the carbs, grasp the bank of carbs from behinde, at the top pulling towards you normaly is enough to remove them as the retaining screws are not always tightly secured but often difficult to see, once removed you can
then prepare the screws ready for re fitting the carbs

Apr 17, 2011 | 2001 kawasaki ZX-6R Ninja

1 Answer

I am helping a friend that worked on his bike and it now fails to start. He removed the carbs and sprayed carb cleaner around and inside the carbs. He then replaced them and the bike won"t start. It is...


Tim, if your friend has sprayed carb cleaner inside the carbs then maybe the needle in the float chamber is stuck. The needle is brass and has been known to "freeze" when sprayed with carb cleaner.
If the carbs have been removed and have been split apart, the chance are they need rebalancing.
I would remove carbs, empty float bowl, spray WD40 around the needle in float bowl, make sure it moves freely whe the carb is held right way up.
Put everything back together, balance them and try again.

Good luck!

Mar 15, 2010 | 1994 Suzuki GSX 1100 FR (Katana)

5 Answers

I need help with removing, cleaning, and installing the carbs. on a 1983 Suzuki gr650 Tempter. I need to be talked to and showed like I am Forrest Gump.


It is actually very simple. The carbs are mounted to the intake by 2 bolts. There is a clamp on the other end that connects the air filter to the carbs. Before removing these connections you will first turn off the gas to the carbs via the petcock at the tank. You will then remove the throttle and choke linkage, (taking note of how it is attached for reassembly purposes). You may now remove first the air filter clamps then the bolts that connect the carbs to the intake manifold at the engine end of the carbs. I suggest you buy kits to rebuild the carbs, they contain needle valve seats and gaskets. You can disasemble the carbs and soak in carb cleaner overnight..then you will blow them out with compressed air. Make sure you remove the plaque build up in the carb bowls. You can now reassemble with the new gaskets and reinstall in reverse order. Good Luck! I hope you find this to be very helpful!

Mar 10, 2010 | 1983 Suzuki Tempter GR 650

Not finding what you are looking for?
1990 Honda GL 1500 Gold Wing Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...