Question about 2003 Yamaha YZ 125

1 Answer

How are the basic setting in the carburator? - 2003 Yamaha YZ 125

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

You have a mikuni carb. there are curcuits to the carb. the first that works from idle to 1/4 throttle is the pilot cicuit, from there you transition to the needle jet/and jet needle. That controls the 1/4 to 3/4 throttle and then the main' jet which controls WOT. you may have a air screw that would be before the throttle plate if it is after it is a fuel screw find the factory specs for the jet sizes and make sure all is correct. if not you isolate where the problem is and correct in a rich or lean adjustment' I race yamaha 2 stroke road racing bikes, it is not an easy task sorry to complicate you so much

Posted on Sep 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is basic carburator settings.


start with 1,5 turns out from the fully seated position. Then fine tune the High and Low
http://www.aerocorsair.com/id150.htm

Jun 10, 2014 | Poulan Garden

3 Answers

Carburator and idle problem


Believe it or not you just said the solution to your own problem manufacturers specs requires for any adjustments to engine idle or other carburator adjustments to be preformed while the engine is idling and at normal operating temp in plain english let the car warm up then make your idle and mixture adjustments if this doesnt solve it i would check the auto choke and make sure it is opening at normal operating temp hope this helps good luck

Sep 01, 2008 | 1984 Toyota Tercel

1 Answer

HOW TO ADJUST CARBURATOR FOR BETTER MILEGE


Hi Anonymous, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
Two Stroke Scooter ATV Carburetor Settings And Adjustments 1of4 Basics...
Bajaj Wave DTS 2006 service manual DOWNLOAD FREE FULLMANUALS COM

Jan 24, 2014 | 2006 Bajaj Wave

1 Answer

Hi i have a 4stroke 125cc pit bike it wont start tried bump start sorted turned over but when i reved it didnt respond then died any ideas


Tryd go to auto shop and check the carburator of your motor and clean your air filter adjust air setting in carburator and put a new fuel pump check fuel setting in carburator

Jan 18, 2014 | Motorcycles

1 Answer

Need carburator adjustments high and low mac 3516


Basic settings one and a half turns out on both screws, you will need to fine tune from there.

Feb 15, 2011 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

How do you set the carburator back to factory specs. mine wont keep running


Basic settings can vary from model to model, a good starting point for most carbs is screw both H and L screw right in ,then back the H screw out 1 turn and the L screw 1 and1/4 turns, the machine should run well enough to fine adjust from there, they are both fuel screws, so the more you unscrew them the richer the saw becomes, always remember if there in another under lying problem adjusting the carb screws will not always help, before any adjustment clean or replace the fuel filter in the fuel tank.

Feb 03, 2011 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

Truck is skipping,cutting back and back firing out the Exhaust is this caused by the carburator


carb can cause alot of head aches but first check basics plugs wires cap rotor i think the ignition timing is out check ignition timing incl is a chart with engine specs set base timing then rev engine up to 1500rpm an timing should advance 110-15 degrees if distributor4 advance is working make sure there is vaccume to distributor advance hope this helps if not let us know the results
shinehutt_16.gif

shinehutt_15.gif

Jan 12, 2011 | 1987 Toyota Pickup

1 Answer

Weedeater carburator setting on bolens 31cc


initial setting is 1and1/4 turns out for walbro carb.
1 turn out zama carb.

May 26, 2009 | Garden

2 Answers

New carburator and it runs worse


Check your fuel pump,it sounds as if you have excessive fuel pressure.

May 05, 2009 | 1984 Ford F 250

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

589 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

dhnguyen

Level 2 Expert

281 Answers

vince

Level 3 Expert

1214 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...