Question about Aermacchi Sprint 350 Motorcycles

1 Answer

Wont start. Turns over works with starter fliuded, change carb out with another one and dumped tank with new feul..acts like no fuel ,, what to do?? ____YY50QT 6 Scooters repair manaue (BY JONWAY)

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Had simular problem with my sl50qt-7 - qmb139 engine - was bad fuel pit **** pump at fuel tank - replaced it and filter and that took care of my problem.

Posted on Oct 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

18 hp v twin Kawasaki won't idle acts like chock is on, not getting full rpm, new carb new fuel pump new air filter runs same without air filter


have u adjusted the carb ? motor with lot of hrs the compression air intake wont be the same as a newer motor like the carb is. feul lines n pump not getting dirt build up from tank?

Apr 17, 2017 | kawasaki Motorcycles

1 Answer

Briggs and stratton engine in rover lawn mower ....... the mower is about 7 years old and maybe used once a year.....the fuel primer button does not seem to be working... please help !


what size motor squirt some starting fliud in the carb and it starts up probably need to rebuild carb no i no you will have to rebuild carb and get this feul additive called sea foam follow the instructions on the can it will make a old machine run like new run to tank fulls through it

Sep 12, 2014 | Garden

2 Answers

I have a 2008 Suzuki S50. It wont start and is dumping fuel from the overflow. Bike has less than 2000 miles on it. It has been sitting for a year. It had about 1/8th of a tank of fuel in it. We...


Take your carb off and apart and clean it throughly. Check your float to make sure its not getting stuck. If it ran fine befor do not tamper with the adjustment. Just free it up with lube then spray it clen with carb cleaner or starter fluid

Apr 19, 2011 | 2008 Suzuki Boulevard

1 Answer

Wont. start, engine turns over, but no fuel is getting to carb.


Fill Your tank with gas and bypass the fuel pump running a fuel tube directly to the carbs from the lower tank. If the bike runs you probably need a new fuel pump.

Jul 11, 2010 | 2004 Honda VT 750 Shadow Aero

1 Answer

Mower starts fine but conks out in about a minute or two.I changed the air filter but it still stalls a minute after starting. toro mower is about 2 years old


Recheck your fuel selector to make sure it is ON. Also if this is the first start of the season there may be old gas / debris in the bottom of the float bowl. One other area to check is the bottom of the gas tank / fuel outlet port of the tank. I don't remember if this model had an in-line fuel filter but also something to check if installed.

This is listed under Toro Mower with power tools that has a 6.5 Briggs and Stratton engine.



To clean the carb passages you will need to do the following.

(FUEL SELECTOR OFF)

1. The adjustment screw on the side of the carb that has a spring on it. You need to count the number of turns it takes turning it clockwise until it just comes up snug NOT TIGHT. Then remove it.

2, Remove the float bowl and dump the contents.

3. Spray carb cleaner in the adjustment screw hole.

4. Disconnect the fuel hose to the carb and spray carb cleaner in the brass tubing hole. The cleaner should be exiting via the float needle. Make sure float assy is down....

5. Connect the fuel line. (use a spray paint can lid and catch the fuel in this step. FUEL SELECTOR on. Catch fuel exiting carb. Lift the float to a LEVEL position and feul flow should stop. DO NOT FORCE IT! Gentle lift only.

FUEL Selector off.

6. Install float bowl

7. Re-install adjustment screw/needle/spring in the side of the carb. Turn it until it just snugs up.. then back it off the number of turns it took to initially close it before removal.

FUEL Selector on... wait 30 seconds..

7. Start mower.

That should do it.

Kelly

May 03, 2010 | Toro Lawn Mower With Toro Power Tools

1 Answer

Wont run without choke being pulled out 1/4 .


INFO:
-Remove Carb and clean, you have a high speed fuel port clogged.

NOTE:
This would also be a good time to replace your fuel lines, Take photos before you start.

RECOMENDATIONS:
-Drain all fuel from the Saws fuel tank.
-Remove and REPLACE with a NEW spark plug.
-Remove and RELPACE with a NEW Air filter.
-With spark plug and air filter removed and fuel drained pull the starting cord many times 12 or so to ensure there is no fuel in the chamber and also check for a spark at the plug.
-RE-MIX WITH NEW FUEL your 2 cycle oil to the correct ratio in a clean fuel can. it is OK to dump some in the Saws fuel tank slosh around and dump out in an approved container for disposal.
-Hold off on putting back on the air filter until you have had it running.

Hope this Tip Helps.

R/
David

Jan 27, 2010 | Poulan Pro 16-Inch 38 cc Anti-Vibration...

1 Answer

The moment the bike stands feul runs into the cranck case and then the fun starts... if it starts up, fuel sprays out the exhausts like a fire hose... is it because my fuel lines are in the wrong position...


The floats in the carbs are sticking open allowing the carb to overflow and fill the crank. Disassemble the carbs for cleaning. Also, turn off the gas tank valve when parked.

Dec 06, 2009 | 1989 Yamaha TZR 250

1 Answer

Will only start with direct feed or starter fliud


Hi and welcome to FixYa,

If after the "...start with direct feed or starter fliud...", the bike will idle / run correctly, then it is not a carb problem. If will not idle / run correctly, then a carb problem.

Initially, it would appear that the problem would be restricted fuel flow from the tank through the petc0ck (fuelcut off valve). A way to check is to drain carb bowls individually, compare quantity and quality of fuel from each. Guesstimate if the collected / drained fuel is about right for the bowl size.

If on the otherhand, it is a carb issue (float closing early hence too little fuel in the bowl), then a carb pulldown maybe required. The illustration here would give you an exploded parts diagram.

This CV carb tuning procedures may interest you.

Good luck and thank you for asking FixYa.

Nov 18, 2009 | 1996 kawasaki ZX-6R Ninja

2 Answers

Acts like it aint getting gas


Have you changed the fuel filter.If you have run a temerary feul pipe from the tank to the carb sounds like a fuel restriction,

May 30, 2009 | 1995 Dodge Neon

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aermacchi Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

magna buff

Level 3 Expert

3828 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

41659 Answers

Are you an Aermacchi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...