Question about kawasaki KX 125 Motorcycles

1 Answer

Bottom end has gone how much to fix it - KX 125 kawasaki Motorcycles

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

That will depend on what model motorcycle you have.
D.

Posted on Sep 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY ENGINE HAS A KNOCK TO IT


you need to establish if its bottom end or top end. if bottom end big end bearings have gone then its a big job ( easier to replace engine ) and if its top end ( cam ) then its a mornings job. big difference. hope this helps

Feb 25, 2012 | 2000 Pontiac Sunfire

1 Answer

I got a 1999 Tahoe with blown head is it worth fixing?


rule of thumb....engines wear as an assembly top end and bottom end
fix the top bottom often goes shortly after
fix the bottom top goes shortly after
used engine with low k's or miles best bet
auto wrecker best source most give warranty some install or can recomend shop to you

Feb 02, 2012 | 1999 Chevrolet Tahoe

1 Answer

I have a accugreen 1000. The wire for the settings has gone slack and I can't adjust the settings. It just stays open. How do I fix this.


You can try to calibrate the spreader, tightening the screw at the end of the control wire should fix the situation. If calibrating the spreader does not help please call us at 800-543-8873 for more assistance. To Calibrate the Accugreen 1000: 1. Adjust the micrometer setting to a 6. 2. Flip the spreader over. 3. Use your foot to squeeze the trigger against the handle. 4. The front edge of the shutoff bar should be aligned with the calibration line engraved on the bottom of the hopper. 5. To adjust the alignment, use a small wrench to turn the black calibration screw at the lower end of the control wire leading from the micrometer insect.

Jun 13, 2011 | RTO Accugreen 1000 Drop Spreader

2 Answers

Hoover oph 714d optima 7kg washing machine fault code e05


Hi


Error code e005 means the temperature sensor has gone bad. To fix this error you'll need to replace the temperature sensor. It might have happened that the temperature sensor wires have been disconnected from the main board. To replace the temperature sensor you'll need to disassemble the washer and inspect the drum's bottom for the temperature sensor. Also check the wires coming to the sensor fro any cut.

Please post back for any further assistance.


Daniel

Aug 01, 2010 | Washing Machines

1 Answer

Told i need a new engine


it means it been run with no oil and now the big ends and crank main bearings are melted to the crankshaft journals

Jun 15, 2010 | 2002 Ford Escort

1 Answer

I have a knocking sound when I am driving my 99 GMC jimmy on the rear drivr side. But there is also a strong smelling liquid leaking into the tire well while driving, what may be the problem and can I fix...


The only liquids it could be are brake fluid and gear oil from your rear end. If there is knocking too, i would guess it to be a wheel bearing and seal are gone. The only way to find out is to pull the wheel and inspect it. As far as fixing it yourself, i don't know what you can do, but if the seal is gone, you have to take the cover off your rear end, and pull the axle.

Apr 05, 2010 | GMC Jimmy Cars & Trucks

2 Answers

My screen has gone to black. how do I fix it?


If you got the phone wet this will happen. Even damp "like in the bathroom while taking a shower." Take the back cover off there is a round dot that should be white. If it is red you got the phone wet and you will need a new one. This cannot be fixed!

Dec 12, 2009 | Motorola Mobility RAZR V3

1 Answer

1999 yz250 engine knocks. First I thought it was on top. However I noticed that when I tried to re-start. There was a knock toward the bottom when using the kick starter. Can someone direct me in the...


hi buddy its either the clutch basket knocking or the small end or big end berings gone/ crank bearing strip the top end and inspect the conrod for movement and bearing crunching and noises also the piston there very easy to strip as its 2 stroke

Aug 30, 2009 | Yamaha YZ 250 Motorcycles

1 Answer

Engine knocking


Hi ...... If your crank, bearings/shells or crankcases have 'gone' it could be very expensive. I would suggest contacting breakers or specialist companies like Partfinders and enquire as to availability of low mileage bottom ends or complete engines. Use what you can from yours then sell any remaining servicable parts you have on Ebay.

Dec 29, 2008 | 1985 BMW K 75 S

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...