Question about 2002 Yamaha TT-R 125

1 Answer

I have a nid 70s enduro 100 it runs great but whaen i put it in gear it jumps a bit then dies it starts in gear as long as the clutch is not engaged im a bit lost ps i do know how to ride so its not me

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

It sounds like your clutches are stuck.If the bike has been sitting for awhile the clutch plates will stick together. Sometimes they will unstick.1st I would change the oil. Then i would place the front tire up against a solid wall start the bike pull in clutch put in gear ,repeat a few times.If this does not unstick the clutch you might have to replace your fiber clutch plates.Hope these helps
D.

Posted on Sep 27, 2010

Testimonial: "thank you i hope it helps too i kinda boiunced back some other thoughts though i havent tried what said yet please follow up if you can thanks again"

  • 1 more comment 
  • travisedo Sep 28, 2010

    it has ran in first gear ocasionally 4 tmes to be exact shifting to 2nd and 3rd is like down shifting how about if i drain the oil and fill it up with deep creep anbd let it set or maybe a penetrating spray drain it then refill it with oil also how much poil what kind and do the gears on this bike go 1 up 3 down or what? im not sure if im just shiftin wrong but i doubt it any help por favor

  • travisedo Sep 28, 2010

    ps thank you ive recently determined its a 78 but how can i be sure with the pre 80 vins its not easy im goin by pictures but thats not ntoo helpful

  • Dietrich Houston Sep 28, 2010

    I would not use any thing other than motorcycle gearbox oil in it. Shift pattern is 1 down for 1st then shift up for 2nd,3rd,4th maybe 5th. So it goes 1down 4 or 5 up. If all you have is motor oil you can use that.
    D.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine dies when putting it in gear


manual transmission ???????
if yes then clutch worn or clutch drive plate problem at a guess

Jan 18, 2017 | Cars & Trucks

2 Answers

Stalls when engaging first gear


Check clutch switch may be stuck bike thinks you are putting in gear without pulling clutch

Mar 11, 2014 | Suzuki DR 350 S Motorcycles

1 Answer

Tranny, linkage or ???


clutch, and check clutch cable linkage. Make sure there ain't no or very little slack in the clutch cable. It dies because the clutch is still engaged with the flywheel. Car won't move in any gear because the clutch prolly needs to be changed.

Feb 06, 2014 | 1987 Acura Integra

1 Answer

CLUTCH ON CITROEN C2 KEEPS DROPPING TO FLOOR AND WHINING SOUND WHEN MOTOR IS RUNNING


It jump because the clutch disc itself is good, but the clutch is not engaging-the pedal is not making the clutch engage. When it does, then you can shift without grinding, then you can shift period. Clutch pedal operates a cable or it operates a hydraulic system-they both, which ever one you have, move the clutch fork on the transmission bell housing just a bit to cause the clutch to disengage the transmission from the engine's flywheel...so you can shift, see, easy, smooth shifts, no problem, no grinding. Your clutch itself is okay, the pedal is just not operating it.

Dec 26, 2013 | Cars & Trucks

1 Answer

My 1989 gsx 600 suzuki jumps when i try to put it in gear


maybe wrong viscosity in the clutch cavity, make sure its the proper oil. then think about making a complete clutch adjustment.
check the service manual for making adjustments.

Nov 11, 2012 | 1993 Suzuki GSX 600 F (Katana)

1 Answer

Engine cuts off when clutch is engaged


check for a bad safety switch on the clutch/brake pedal try and jump it with a paper clip

Jun 11, 2012 | Garden

4 Answers

What's your problem?1995 yamaha virago 1100 that sometimes you you put into gear and immediately dies


The Clutch on some bikes will disengage the starter motor. Yamaha will not allow you to engage gear when the side stand is down. Hope this gives you some idea

Nov 27, 2011 | Yamaha Motorcycles

2 Answers

With the bike in gear and the clutch engage, the


Clutch discs are stuck, put the bike in gear, not running, pull in the clutch and push the bike back and forth to break the clutches loose. Once they break loose start the engine put the bike in gear, hold the front brake, and slip the clutch a little to remove any built up or stuck crud on the plates.

Mar 10, 2010 | 2000 kawasaki VN 800 Vulcan Classic

2 Answers

Yamaha Enduro Clutch not engaging


i actuall have a yamaha enduro 100 and had this same problem.
First thing is take the clutch apart take all the rings out and clean them good with momry cloth assemble the clutch compleatly as it came out and when tighting the springs tight them all one turn at a time and after everytime you go around try to move youre clutch with youre bike in gear. if it trys to move it is engageing just keep turning the screws untill they stop. also recomend putting threadlocker on the drive gear bolt and the clutch bolt that holds the clutch on. if you have and questions just e-mail me at Jvossbrink@comcast.net just make shure to tell me that i responded to youre fixya question about youre bike and i will walk you threw it.

ps just rember to put the clutch pushrod back in

Aug 02, 2009 | 1974 Yamaha DT 360

1 Answer

When I put it in gear it dies even with the clutch engaged


Check out your kickstand switch. kickstand must be up to move in gear.....safety

Feb 03, 2009 | 2006 Suzuki GSX-R 750

Not finding what you are looking for?
2002 Yamaha TT-R 125 Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...