What are the tourque settings for bolts on the flywheel when i attach the clutch and pressure plate for a toyota corolla 2001.

Was the flywheel machine smooth along with the new clutch? Was the pressure plate and disk replaced as a set? If the flywheel was not removed and machined then you have found your problem.

there is usually and access cover on the bottom right behind the oil pan, the bolts are on the back of the flywheel. This is true with most automatics but if it is different I know a guy who has changed these out before that I can ask.

Removal & Installation To Remove:

1. Remove the transmission.
2. Install a flywheel locking tool.
3. Remove the pressure plate mounting bolts from the flywheel.
4. Remove the pressure plate and clutch disc.

To Install:

1. Insert a clutch disc alignment tool through the disc splines and into the flywheel pilot bearing. Pressure plate balance mark location
   
   
2. Install the pressure plate on the flywheel with a gap of 120° or more between the "0" balance marks on the flywheel and pressure plate. Hand tighten the pressure plate mounting bolts.
3. Tighten the pressure plate mounting bolts using a crisscross pattern 12 ft-lb (16 Nm).
4. Remove the clutch disc alignment tool.
5. Install the transmission.

Clutch disc and pressure plate. The bolts should be tightened in 2 or 3 steps, gradually and evenly. Final bolt torque is 14 ft. lbs. (19 Nm).

the flywheel is balanced by its self but the clutch is not,,,you may have got a bad clutch thats well out of balance,,and you may need to swop it out again,,but,, first check that all the gearbox bolts are up tight and its not the box moving

Sounds like the clutch plate is not aligned with the transmission pinion. Also check to make sure the clutch plate was not installed in reverse. Your pressure plate should be installed flush with the flywheel. If you are not using a clutch alignment tool, you should.

REMOVAL:

1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
3. Raise and support vehicle.
4. Remove clutch release lever dust shield.
5. Disconnect clutch release lever cable from clutch release shaft.
6. Remove retaining clip, then clutch release lever cable from flywheel housing.
7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
8. Remove transmission.
9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
11. Remove clutch release hub and bearing from clutch release shaft.
12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
13. Remove clutch pressure plate and clutch disc from flywheel.

INSTALLATION:

1. Position clutch disc and pressure plate assembly on flywheel, noting following:
   1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
   2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
   3. tart clutch pressure plate bolts but do not tighten.
   4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
   5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
   6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.
   
   
2. Install transmission to flywheel housing.
3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
5. Install starter motor.
6. Lower vehicle, then install clutch release lever cable as follows:
   1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
   2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.
   
   
7. Cycle clutch pedal several times to adjust clutch release lever cable

Below is process for removing and replacing the clutch assembly.
Hope this helps, good luck.
Regards,


REMOVAL & INSTALLATION


See Figures 1, 2 and 3



Fig. Fig. 1: Exploded view of the clutch disc and cover assembly

1. Disconnect the negative battery cable.
2. If equipped with a cable clutch (1982-84 vehicles), disconnect the cable at the clutch release lever and transaxle, as outlined earlier in this section.
3. For 1985-94 vehicles remove the sound insulator from inside the vehicle. Disconnect the clutch master cylinder pushrod from the clutch pedal.

Fig. Fig. 2: Disconnect the clutch actuator (slave) cylinder line - 1995-96 vehicles

1. Remove the transaxle, as outlined earlier in this section.
2. Mark the pressure plate assembly and the flywheel so that they can be assembled in the same position. They were balanced as an assembly at the factory.
3. Loosen the attaching bolts one turn at a time until spring tension is relieved.
4. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc. Do not disassemble the pressure plate assembly; replace it if defective.
5. Inspect the flywheel, clutch disc, pressure plate, throwout bearing and the clutch fork and pivot shaft assembly for wear. Replace the parts as required. If the flywheel shows any signs of overheating, or if it is badly grooved or scored, it should be refaced or replaced.

Fig. Fig. 3: You must follow the specified sequence when tightening the pressure plate retaining bolts
To install:

1. Clean the pressure plate and flywheel mating surfaces thoroughly.
2. Position the clutch disc and pressure plate into the installed position, and support with a dummy shaft or clutch aligning tool, tool J 29074 or equivalent. The clutch plate is assembled with the damper springs offset toward the transaxle. One side of the factory supplied clutch disc is stamped "Flywheel Side".
3. Install the pressure plate-to-flywheel bolts. Tighten them in the sequence shown in the accompanying figure, as follows:
   1. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 12 ft. lbs. (16 Nm).
   2. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 15-22 ft. lbs. (22-30 Nm) plus an additional 30° turn.
   3. Remove the clutch alignment tool.
   
   
4. Lubricate the outside groove and the inside recess of the release bearing with high temperature grease. Wipe off any excess. Install the release bearing.
5. Install the transaxle, as outlined earlier in this section.

WARNING When adjusting the cruise control switch, do NOT exert an upward force on the clutch pedal pad of more than 20 lbs. (89 N) or damage to the master cylinder pushrod retaining ring may result.

1. For 1985-94 vehicles, attach the clutch master cylinder pushrod to the clutch pedal and secure with the retaining clip. If equipped with cruise control, check the switch adjustment at the clutch pedal bracket. Install the sound insulator.
2. If equipped with a cable clutch, attach the clutch cable at the transaxle and clutch release lever. Check the clutch operation by lifting the clutch pedal up to allow the mechanism to adjust the cable length. Depress the pedal slowly a few times to set the pawl into mesh with the quandrant teeth.

ADJUSTMENTS


All 1982-84 models have a self-adjusting clutch mechanism located on the clutch pedal, eliminating the need for periodic free play adjustments. The self-adjusting mechanism should be inspected periodically as follows:

1. Depress the clutch pedal and look for the pawl on the self-adjusting mechanism to firmly engage the teeth on the ratchet.
2. Release the clutch. The pawl should be lifted off of the teeth by the metal stop on the bracket.

On 1985 and later models, the hydraulic clutch system provides automatic clutch adjustment. No adjustment of clutch linkage or pedal position is required.

I see. sounds like you need a new clutch. OK, here is a step by step guide to follow. it will help with the removal and installation of your new clutch.

Remove the Old Clutch Step1 Verify that your vehicle's clutch is the source of your problems and not the pedal-arm bushings, activating cables or the slave-master cylinder. Step2 Unhook the positive battery cable, the clutch cable or hydraulic slave cylinder to get the transaxle ready for easy removal. Eliminate anything that may hinder your efforts, including exhaust pipes and the speedometer. Step3 Secure your car in a safe position before jacking up the front end. Step4 Stabilize the engine with a jack below the oil pan. Remove the transaxle by undoing at least one engine mount. Step5 Separate the engine from the transaxle by removing the bolts that surround the flywheel bell housing. Step6 Push the transaxle away from the engine until the input shift clears the pressure plate. Step7 Disengage the bolts surrounding the pressure plate and take it and the clutch disc out. Check to see if the flywheel's friction surface is scored, checked or has hot spots. Remove, machine and reinstall the flywheel, if needed. Step8 Examine the pilot bearing (bushing) located at the flywheel's center to be sure the needle bearings are lubricated and that there's no galling. Also look for any oil leaking around the rear main engine seal. Replace the clutch Step1 Follow the instructions for replacing your car's clutch carefully to avoid having to remove the transaxle. Step2 Check that the transaxle's input shaft isn't leaking; replace if needed. Step3 Take out the flywheel and the old seal and install a new seal. Install a New Clutch Step1 Clean the crankshaft flange before putting in the flywheel. With the flywheel on top of the flange, secure the bolts in a star formation to the specified torque for your vehicle. Step2 Install the clutch disc and pressure plate. Prior to putting in the transaxle, attach the new release bearing to the release fork. The fork should move freely. Step3 Hoist the transaxle into position and move it forward until the input shaft glides into the clutch disc's spindled hole. Do not apply force. Step4 Reinstall any bolts or mounts that were removed to replace your car's clutch. Grab the transaxle, release the jack and lower your vehicle. Step5 Consider replacing your car's clutch cable. If you don't replace the cable at least adjust it for the right amount of free-play. Step6 Confirm that your clutch's self-adjusting action is performing correctly by depressing the slave cylinder's piston into its bore. Step7 Drive your car to be sure your clutch is working properly.


PLease rate and god bless:)

You car does not have an "adjustable" clutch. The Corolla uses a hydraulic clutch. The action of the hydraulics eliminates the need for adjustements. If the clutch is slipping, you may need to replace the clutch.