Question about 2001 Harley Davidson FLHRCI Road King Classic
Well, it probably has a fuse but there could be more on that fuse than just the alarm. With thieves getting more aggressive, I fear disconnecting it is a bad idea.
A friend had neighbors complaining that his car alarm kept going off. so he quit setting it. A few nights later someone broke in stole the fancy radio, the air bag, and the seats. They were deliberately causing the alarm to go off. Eventually when it didn't go off, they knew they were safe to steal all the good stuff.
If the alarm is causing problems, the dealer might be able to loosen the parameters on the sensors. I would give that a try first.
Posted on Jan 15, 2015
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The Road King shocks are air adjustable via an air valve located on the right side of the bike just above the rear tire. Your Harley Davidson owner's manual will tell you what the shocks should be pressurized to depending upon the load on your bike (for instance - if you'll be carrying a passenger - the pressure should be a bit higher than it would be if you were riding solo). Don't even attempt to read the pressure unless you have the specialized hand pump that is used to pressurize the shocks. You can purchase this from Harley Davidson or via a third party online. The valve is a typical bicycle / auto air valve - but ... DO NOT attempt to pressurize it with anything but the specialized hand pump. Using anything else will risk over pressurization of your shocks and that's not good. The shocks hold a very small volume of air at relatively low pressure levels - so the hand pump is a must have.
Posted on Nov 10, 2008
I am having problems viewing the reply but if you have a FLHRCI then to replace the fuel filter you will need to be prepared to put some time into it.
First remove the console off the fuel tank, one nut below speedo and the phillips screw lower close to the seat. You will have a disconnect on the top left side of the fuel tank to disconnect. Then disconnect the vent tube from the tank with a gentle pull & twisting motion. Now the fun part there are ten torx T20 screws you need to remove, but first you must go buy new ones along with the gasket and fuel filter kit. DO NOT reuse the screws. Now for whatever reason they call this piece a canopy, go figure. Once you have your parts go ahead and raise the canopy slightly and twist it to the left a little. Now this can be tricky because there is a spring loaded hng to work here, be care not to over stress any thing. Then you can begin to pull the canopy and components from the tank. You will be limited by the convoluted tubes (hose) attached as to how far you can raise the canopy, if you remove one be careful as where they attach is plastic and breaks....easily sometimes, then you need a $350 part.
Next read and look at the diagrams that come with your new fuel filter to install it. Once done carefully reverse the canopy removal process and tighten the canopy bolts in cross pattern o somewhere between 18-27 in-lbs. Hope this helps.
Posted on Aug 15, 2009
Tips for a great answer:
Mar 10, 2014 | 2001 Harley Davidson FLHRCI Road King...
Jan 18, 2014 | 2003 Harley Davidson FLHRCI Road King...
Sep 14, 2013 | 2004 Harley Davidson FLHRS - FLHRSI Road...
Nov 15, 2012 | Harley Davidson FLHRI Road King...
Feb 04, 2012 | 2001 Harley Davidson FLHR - FLHRCI Road...
Nov 25, 2010 | 2004 Harley Davidson FLHRCI Road King...
Jul 25, 2010 | 2003 Harley Davidson FLHRCI Road King...
May 06, 2010 | 2001 Harley Davidson FLHRCI Road King...
Apr 06, 2010 | 2001 Harley Davidson FLHRCI Road King...
Apr 21, 2018 | Motorcycles
153 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: