Question about 2008 Harley Davidson FLHX Street Glide

1 Answer

Bus er showing on display engine light battery light security light comes on an off bike runs fine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,748 Answers

Hi Carolrichbur, for more information about your question please visit the website below. Good luck and have nice day.
Harley Diagnostic Codes 04 to Present

Posted on Jun 08, 2015

5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: bike sputters at mid to high speed.

the ignition coil is going bad probably overheating

Posted on Mar 23, 2009

  • 119 Answers

SOURCE: Engine Light Going On/Off

yes it could cause this
fully charge battery and try again

Posted on Nov 02, 2009

  • 623 Answers

SOURCE: engine light on

You'll probably need an HD scan tool to reset the bike's computer to clear the code.

Posted on May 08, 2010

  • 195 Answers

SOURCE: 2005 ultra classic.when i turn

Maybe a bad ground Batt to the frame, often the nut that hold the ground cable is rusted., you have to remove the nut and scrape the area that hold this nut ans cable

Posted on May 12, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does no bus means when it showing in your automobile display in a chrysler 300 year 2006

"No Bus" means the data cable going to the (PCM) computer is unplugged, or the PCM has failed.
Maybe a bad crank or cam sensor could be the reason.
Try wriggling the PCM / wiring
Disconnect the battery negative then unplug and plug back in the PCM connectors. Reconnect battery and run engine.

Aug 06, 2014 | 2006 Chrysler 300

1 Answer

Why does a bus er code comes up on my 2007 Harley Davidson ultra glide

"BUS Er" indicates Serial data bus shorted low/open/high. It is number 1 priority DTC fix

If speedometer reads "BUS Er" with the ignition key turned ON with the run/stop switch at RUN with the engine off, check the data bus for an open or short to ground between the data link connector [91A] terminal 3 and ICM connector [10B] terminal 12 on carbureted models, AND on EFI MODELS, ECM connector [78B] terminal 5 , TSSM connector [30B] terminal 3, speedometer connector [39B] terminal 2 or if a tachometer is installed, tachometer connector [108B] terminal 2.

Also check for an open diagnostic test terminal between the data link connector [91A] terminal 3 and the TSM/TSSM connector [30B] terminal 3. With the ignition key turned ON, serial data bus voltage should be typically 0.6-0.8 volts. The range of acceptable voltage is 0-7.0 volts.

Wiggle the instrument and/or vehicle harness to identify possible intermittent problems.

Jul 11, 2014 | 2006 Harley Davidson FLHTI Electra Glide...

1 Answer

BusEr code came up won't start?

BUS ER = 1 Serial data bus shorted low/open/high
DTC U1300, U1301 OR BUS ER:
U1300 = Serial data low
U1301 = Serial data open/high
Serial Data Low or Serial Data Open/High.The typical serial data voltage range is 0 volts (inactive) to 7 volts (active). Due to the short pulse, voltages will be much lower on a DVOM. In analog mode, a DVOM reading serial data will show continuous voltage when active,
typically 0.6-0.8 volts. The range for acceptable operations is
0-7.0 volts.

If serial data is shorted, these Diagnostic Trouble Codes
(DTCs) will automatically cause the check engine lamp to
illuminate. The odometer will read "Bus Er" in this condition.
• DTCs P1009 and P1010 may accompany DTCs U1300
and U1301.
CHECK FOR FURTHER DTCs SET For further diagnosis one needs to know if the bike starts then stalls.

May 04, 2014 | 2009 Harley Davidson FLHX Street Glide

1 Answer

My 2007 Ultra started having speedometer and tach failures also the engine light and security light came on. The bike continued running strong with no change but everthingg listed would continue to go back...

sounds like a computer glitch the only thing you can do is take it to the dealer and get them to put there computer on it and reset,or sometimes just take the positive battery wire off leave it 20 minutes then connect up and see if has reset .hope this helps

Aug 30, 2013 | 2001 Harley Davidson FLSTF - FLSTFI Fat...

1 Answer


Do you have the turn signal security on your bike? If so, have you made sure it is not set and the battery is good in the key fob?

Mar 30, 2011 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

While out riding my HD 1200C, the check engine light went on and off several times. The bike had been sitting for a couple of weeks. The bike was running fine but that light concerns me

Those engine lights come on because something is causing an engine code, the code can only be read by the HD dealer with their digital tech program. They plug your bike into it and it displays the error code, they may be able to delete the code and it might never come back again or there might be a real problem.

Jun 28, 2009 | 2005 Harley Davidson XL 1200 C Sportster...

1 Answer

Bus er eror code on mileage display

Hi Sticktch, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Diagnostic Codes 04 to Present

Mar 14, 2009 | 2006 Harley Davidson FLHRI Road King

3 Answers

2005 Triumph Daytona 955i Dead Battery and Check engine Light

I have just found my 30 amp fuse blown on my daytona , this prevents the alternator working , it was reading 10.9v before I changed the 30 amp fuse , now it reads 14.5 volts , I think I blew it as I didnt know how to put the alarn into service mode and left the ignition on , anyway I am hoping its just that , 3 heat up/cool down cycles and the engine management light should go out


Dec 24, 2008 | 2005 Triumph Daytona 955i

Not finding what you are looking for?
2008 Harley Davidson FLHX Street Glide Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers


Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides