Question about 2001 Harley Davidson FXDXT Dyna Super Glide T-sport

1 Answer

Front break hand control needs ajusting.how is this done?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

There are no adjustments on the front brake hand control. If the lever is too low, check the level of the fluid in the master cylinder. Add on the correct type of fluid as listed on the master cylinder top. Do not mix different types of brake fluid.

Good Luck
Steve

Posted on Sep 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Holden commodore problemsi have a vy commodore brakes just re-knewed but carnt see where to adjust hand break cable mcan u help


most times the hand brake top screws down to adjust the brake but there is normally an adjustment under car where the cables from the rear wheels join the single cable going to the hand brake If the hand brake top has been screwed down all the way loosen it up al the way before adjusting anything

Aug 20, 2014 | Cars & Trucks

1 Answer

Mongoose index 3.0


On the right hand side of the crank or oppisite side of the front sprocket should be a 1 1/8 lock nut remove lock nut an washer should be an ajustable race with two holes known as a spanner race tighten up the race reinstall washer an lock nut tourqe down lock nut rotate crank making sure bearings dont drag an done

Jun 24, 2014 | Mongoose Cycling

1 Answer

Hand brake


when u say new in front or back hand brake controls the rear only .if rear are new ajustment may need to be done

Aug 28, 2013 | Brakes for Chevrolet Cruze

1 Answer

How do I tighten the hand brake cable on my 94 Toyota Tercel?


First make sure the rear breaks are ajusted or replaced when worn out drum to be skeemed aswell. Usally whe rear brakes are ajusted hand break will stop car on two to four clicks on hand brake rachet. If brakes is ajusted check cables for wear . Then ajust cable insite car remove hand brake cover and you will see a ajustable screw or nut. Rememeber to put the handbrake on four clicks and dont tighten screw or nut to much the brakes will lock

Feb 12, 2013 | Cars & Trucks

1 Answer

My brake pedal gets real hard while driving and brakes start to drag


they could be binding on also get the breakes checked see how much frivtion material is left on them incase the calipers are at the maxamum they can go jack the car up when its been running and spin the rear wheels to see if there draging if so check hand break ajustment and rear shoes for same as front if all this is ok then move onto master cylinder if this is starting to go this can make the pedal feel hard also get the servo unit on the front of master cylinder checked as this is where the power comes from to make the car stop check hoses and pipes for leaks or cracked pipes hope this helps ivan

Oct 03, 2012 | 1998 Toyota RAV4

2 Answers

How do i adjustment the handbrake on a rover 75 on a rover 75


should be self ajusting if not there should be a nut conected to the hand breake either remove cowling around hand brake if not i may be underneath the car where hand brake comes out of the floor but most cars now can be ajusted by removing the hand breke trim

Sep 19, 2012 | 1999 Toyota Corolla

1 Answer

I HAVE A MAZDA 323 1999 MODEL CAN ANYONE TELL ME HOW TO ADJUST THE HANDBRAKE PLEASE please note it is a 1999 model but it wont let me put that year in


your handbreak connects to the rear breaks follow the cable from your break drum where the 2 meet is the ajustment give it a squart of penertrating oil before ajusting as it has been open to the weather also there is further ajustment where the cable enters the hand break lever good luck ps if this dosent do the trick i suggest you cable is fully streched you will need to fit a new one

Nov 15, 2009 | 1986 Mazda 323

2 Answers

Want DEFLECTION SETTING for my samsung plano 29 inch gigabass tv


I need the deflection constant from Samsung factory for adjustment TV Samsunng Plano of me.

Nov 08, 2009 | Samsung Televison & Video

2 Answers

Rear discs and handbrake on 2002 S80 D5


tighten the hand brake tensioner

Jun 27, 2009 | 2002 Volvo S80

Not finding what you are looking for?
2001 Harley Davidson FXDXT Dyna Super Glide T-sport Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...