Question about Harley Davidson FLHTC - FLHTCI Electra Glide classic Motorcycles

1 Answer

How do you ajust rear wheel so it is alignedright?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

1.loosen the bolts on either side of the bike at the rear of the frame. this is what allows the back wheel to be adjusted. aka wheel adjusters.

2.next loosen the wheel itself.

3.pull the wheel back until there is just a tiny bit of slack in the chain.

4.next tighten those wheel adjusters on either side of the wheel. To get the wheel dead centered count the threads visable and make them the same on both sides.

5.tighten the wheel back up as you pull it back against the wheel adjusters.

good luck and safe riding

Posted on Sep 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After a hit the ditch the car dog tracks and the pasenger rear wheel seans to be 3/8 of an inch further back than the drivers side is there rear wheel alignment or ajustment


You aren't saying what type of car you are referring to, but if you are as far out of alignment as you claim to be, you probably are not going to be able to adjust your way to alignment. Something is definitely bent or broken and will need to be straightened or replaced.

Jul 08, 2015 | Cars & Trucks

1 Answer

Holden commodore problemsi have a vy commodore brakes just re-knewed but carnt see where to adjust hand break cable mcan u help


most times the hand brake top screws down to adjust the brake but there is normally an adjustment under car where the cables from the rear wheels join the single cable going to the hand brake If the hand brake top has been screwed down all the way loosen it up al the way before adjusting anything

Aug 20, 2014 | Cars & Trucks

1 Answer

How do I tighten the hand brake cable on my 94 Toyota Tercel?


First make sure the rear breaks are ajusted or replaced when worn out drum to be skeemed aswell. Usally whe rear brakes are ajusted hand break will stop car on two to four clicks on hand brake rachet. If brakes is ajusted check cables for wear . Then ajust cable insite car remove hand brake cover and you will see a ajustable screw or nut. Rememeber to put the handbrake on four clicks and dont tighten screw or nut to much the brakes will lock

Feb 12, 2013 | Cars & Trucks

1 Answer

The left rear brake auto ajustment will not stay set i have replaced the front rotors and pads also a complete rear brake job including new spring kit and shoes and new drums. the left rear is ok for a few...


if the wheel cyclinder is bad it will either bleed off causing the brakes to feel soft or the pins could be stuck causing them to drag. also check that all the springs were replaced in the proper location or it may not be holding the adjuster where it needs to be.

Apr 05, 2011 | Chrysler Cirrus Cars & Trucks

2 Answers

Loud noise


nost likely the color wheel, They are famous for having a piece come off the wheel which will cause a very loud humming sound.

Jan 15, 2010 | Samsung HLR5067WX 50" Rear Projection HDTV

1 Answer

Rear brakes


you need to turn the adjuster
there is a little hole on the bottom of your backen plate to ajust the brakes up

Oct 06, 2009 | 1997 Mercury Tracer

2 Answers

How do you adjust parking brake On A Kia Sedona


Underneath your vehicle, a steel threaded cable comes from the back of one hub and is joined by a short cable from the other hub--then the original cable runs to a threaded end with an adjuster nut in it--and one smaller nut on the end outside of that--(this is the equalizer bar)--you'll see it real close to your transmission.
You might have to jack-up the back of the vehicle???
Pull the parking brake lever up sharply and then release it.
Pull the parking brake lever to the second click and leave it there. You're looking for a slight drag of the brake shoes when you spin the wheels.
To increase the drag, get under at the equalizer bar and turn the adjusting nut to take up the slack in the cables. Get out and spin the rear wheels if you think it's to tight.
I will say don't be afraid to crank on it for a while as in this case, a little adjustment really does not go a long way. When you think you have the drag right, go back in the car and pull the brake up the the fourth click. At this point the wheels should be locked and you should not be able to turn them even when trying hard. If you can, tighten them up a little more.
Once you've done this, release the brake and make sure the wheels spin freely. If they are still binding due to the parking brake, back off the adjustment a little. And that's basically the whole adjustment procedure.

Sep 28, 2009 | 2002 Kia Sedona

2 Answers

Need to know how to adjust the rubber drive wheel on a rear engine snapper. Any help will be great. Thank you


Usually just replacing the drive wheel will fix the problem. There are two allen head set screws on the disc mounted on the engine shaft visable through the hole in the rear of the mower. However, don't expect when you loosen them that the disc will move up or down freely. I've only ever move one by taking the engine off. I'd try replacing the rubber drive wheel first.

Jun 14, 2009 | Omega Rear Drive Wheel Snapper Mowers

1 Answer

93 Ford thunderbird parking brake adjustment


on most of the cars us use a special spanner tool that resembles a bent screwdriver. you pull the plastic cap out from the back of the drum and then just turn the ajustment wheel till you feal it tighten up a litle. Remember to put the plastic cap back on. Also a old trick most people don't know about is put the car in reverse in a parking lot, and slam on the brakes. most cars have a auto ajustment that they never use.

Jun 14, 2008 | 1993 Ford Thunderbird

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...