Question about 1996 kawasaki ZX-9R Ninja

Open Question

Zx9r 1998 - where does the horn bracket mount to.... radiator ,fairing or steering head ?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tellme2
  • 137 Answers

SOURCE: 1998 ZX9R C1: Fairing damage. What do I fix it with?

ello mate,, well theres some basturds about ay,, this happened to me once,, any way,, to bond a crack or build up a hole, turn the fairing round so u r lookin at the back of it, rough the crack or hole up with some sand paper,, then get your self some fibre glass matting wad,,and some resin, and hardener, using scissors cut the matting out to shape mix up some resin and apply to the back of the fairing,, this is messy stuff ,,but will bond it well,,then turn it over ,,if u still have a visible crack and want to repair that,, then run a grinder down the crack ,,so it widens the crack just a bit ,,and fill it with isopon filler,, just the normal kind of filler, for dents etc,,

Posted on Mar 24, 2009

Ad
  • 1 Answer

SOURCE: Will 2001 zx9r fairings fit the 1998 zx9r????

will fairings from a kawasaki zx9r 98 fit on a zx9r 97??????

Posted on Apr 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I wire a horn on a 1995 chev truck


Is there a problem with horn wiring in the steering column? The safest fix is to fix so the horn button on the steering will work. I'm not sure I understand your problem?

You could mount a separate horn button on the dash, but, that isn't the safest thing to do because your used to the horn button on the steering wheel.

If you mount a separate horn button, all you need is the horn ground that goes up the steering column, it is black. Find the harness under dash that goes into your steering column, black wire, just to test, use jumper wire from that wire to good ground, if the horn starts sounding, that's it. Run that wire to horn button. Also, you may need to run second ground from that horn button, if it doesn't ground through mounting bracket.

Mar 01, 2015 | Cars & Trucks

1 Answer

Will 2000 zx9r fairings fit on 1998 zx9r


in my experience the 2000 fairing is different including the front headlight bracket the 1999 will fit cheers

May 26, 2014 | Motorcycles

1 Answer

Horn location


Horns are on the radiator support bracket just behind the grille on the lower end of the bracket. The horn button on the steering wheel operates the horn relay in the under hood fuse box. Test it to see if it works.

May 18, 2014 | 2002 GMC Envoy

1 Answer

Replace car horn


1. Pop the hood and locate the horn. These are typically mounted to the grille or on a bracket in front of the radiator.

2. Loosen the hardware that attaches the horn to the car with a hex wrench or screwdriver. Horns are usually mounted with two hex nuts and bolts although some models may use screws to mount the horn. Remove the hardware then remove the horn assembly by sliding it off the bracket.

3. Disconnect the horn's electrical connectors from the wiring harness by depressing the connector tab on the top of the connector then sliding them free of the connection.

4. Connect the new horn connectors and install the new horn on the mounting bracket. Install the mounting hardware. Tighten using the appropriate tool, either a wrench or screwdriver depending on the hardware and mounting bracket.



Google SinoyElectron to learn more about car diagnostic

Sep 02, 2012 | Mitsubishi Cars & Trucks

1 Answer

Horn doesnt work on 1997 olds aurora. how do i locate the horn. I checked the fuse and it is okay


The horn will usually be mounted in the front of the vehicle usually in front or near radiator. Black plAstic 4.5 inch diameter.

Will usually be mounted by a flimsy bracket. In not mounted near or on radiator I'd check te firewall. The aurora has alot going on in the engine bay so it may take a few mi urea to find

Oct 17, 2011 | 1997 Oldsmobile Aurora

1 Answer

NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


Cylinder Head Removal & Installation 5.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant.
  3. Remove the air cleaner assembly.
  4. Remove the upper radiator hose.
  5. Remove both heater hoses.
  6. Disconnect spark plug wires at distributor cap.
  7. Remove distributor cap.
  8. Remove the coolant bypass hose from the water pump.
  9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
  10. Remove the A/C compressor from the mounting bracket and set it aside.
  11. Remove the wiring bracket from the rear of the cylinder head.
  12. Disconnect the accessory bracket and slide forward.
  13. Remove the upper and lower intake manifold.
  14. Remove the exhaust manifolds.
  15. Remove the valve rocker arms and pushrods.
  16. Remove the power steering pump pulley.
  17. Disconnect the electrical connector from the power steering pump.
  18. Remove nuts attaching the power steering pump to the engine.
  19. Remove power steering pump mounting bracket bolts and nut.
  20. Slide power steering pump/bracket assembly forward and remove stud.
  21. Set power steering pump/bracket assembly aside.
  22. Disconnect the wiring bracket from rear of the right cylinder head.
  23. Remove the generator.
  24. Remove the oil indicator tube bracket bolt.
  25. Remove the generator mounting bracket.
  26. Remove the sixteen cylinder head bolts.
  27. Remove cylinder heads and gaskets.
  28. Clean all sealing surfaces.
To Install:
Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the generator mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the generator mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the generator.
  16. Install the oil indicator tube bracket bolt.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.
Left Side To Install:
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the power steering pump mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the power steering pump pulley.
  16. Connect the electrical connector to the power steering pump.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.

Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

My car's horn actives every time I turn the steering wheel. What do you think is causing it to go off?


My 2000 Cirrus had the same problem.

Before I describe how I fixed mine, a warning and disclaimer:
Working on the horn switch, clock spring and steering column requires working safely with the air bag module. An airbag that goes off unintentionally can cause serious or fatal injuries. If you don't know how to handle the air bag safely, do not attempt to fix this yourself!

Symptom: Horn sounds when steering wheel is turned or with slight movement of the air bag module in the center of the steering wheel.

Possible causes:
1. Deteriorated insulators under the air bag mounting bracket screws. (This is what caused the problem in my case.)
2. Warped or bent steering wheel or air bag module.
3. Short circuit in clock spring assembly.
4. Short circuit in steering column due to abraded or pinched wire.
5. Faulty horn relay. (Very unlikely if the horn only sounds when turning the wheel.)

How the "horn switch" works: The term "horn switch" is a bit of a misnomer because there is no identifiable "switch" as one might think. The "switch" is actually a combination of parts: The four air bag bracket mounting screws, four plastic bushings and washers that insulate the air bag mounting brackets from the screws which are fastened to the grounded steering column, four springs under the bushings and the metal back side of the airbag module. The horn wire, which comes from the horn relay up the steering column and through he clock spring, is connected to the left hand mounting bracket which is electrically connected to the back of the airbag module which is electrically connected to the right hand mounting bracket when everything is assembled. When the air bag module is pushed in, the metal back contacts one or more of the four air bag module mounting screws completing the circuit to ground and thus activating the horn relay.

Troubleshooting:
1. Disconnect the negative battery terminal on the strut tower under the hood and pull the two 10 A air bag fuses from the fuse panel on the left side of the dash.

WARNING!: WAIT TWO MINUTES TO ALLOW THE AIR BAG SYSTEM CAPACITOR TO DISCHARGE BEFORE PROCEEDING. NEVER DISCONNECT OR RECONNECT THE AIR BAG MODULE ELECTRICAL CONNECTOR UNLESS THE NEGATIVE BATTERY TERMINAL HAS BEEN DISCONNECTED FOR AT LEAST TWO MINUTES. FAILURE TO HEED THIS WARNING COULD RESULT IN UNEXPECTED DEPLOYMENT OF THE AIR BAG RESULTING IN INJURY OR DEATH.

2. Loosen the two torx head screws on the back of the steering wheel that secure the air bag module to the wheel. The screws are captive in plastic retainers, so don't try to remove them.

3. Remove the air bag module, pull out the connector lock and disconnect the air bag module connector.

4. Place the air bag module on a flat surface connector side down away from where you are working.

5. Locate the four air bag mounting bracket screws. Look for black gritty debris around the screw heads and inside the steering wheel. This is an indication that the top insulating washers have deteriorated allowing the mounting brackets to short out to the screws.

6. Now reconnect the battery negative lead and do the following tests:

a. Move the left hand bracket slightly. If the horn sounds, then the top side insulating washers are either gone or deteriorated. If you want to test the right hand bracket, you will need to connect a jumper wire between the brackets. If one washer is cracked or missing, it is likely they all are.

b. Disconnect the horn wire from the left hand bracket. Start the car and turn the steering wheel to the stop in both directions. If the horn still sounds, then you have either a bad clock spring or a short circuit in the steering column.

The repair if the insulating washers are bad:

The official Chrysler repair manual says to replace the steering wheel (about $260); however, there is a cheaper solution.

1. Remove the four air bag bracket mounting screws, bushings, springs and the two brackets, paying careful attention to how they are assembled so you can re-assemble them later.

2. Clean any debris, dirt and grease from the brackets and undersides of the screw heads.

3. Purchase or fabricate some thin insulating (plastic) washers to replace the ones that deteriorated, which unfortunately you cannot buy from Chrysler. I insulated my brackets and screws with kapton insulating tape plus some very thin plastic washers I cut from some blister pack packaging scrap (probably clear polystyrene). This plastic is very thin, but still is pretty tough. Some hollow punches are handy for punching the holes and making nice round washers, but you could probably do it with small scissors or your wife's scrapbook punches if you are careful.

4. Reassemble the air bag mounting brackets to the steering wheel placing the new insulating washers and/or tape between the screw heads and brackets.

5. Reconnect the horn wire to the left hand bracket and move the bracket around a bit. If the horn doesn't sound, then you likely have fixed the problem. Once again, to test the right hand bracket, you need to jumper the left and right brackets together.

6. Disconnect the negative battery lead and wait at least two minutes before proceeding to ensure the air bag capacitor is discharged.

7. Reconnect the air bag connector to the air bag module and insert connector lock.

8. Reassemble the air bag module to the steering wheel.

9. Reconnect the negative battery lead and test the horn. It should blow only when the air bag module is pushed in. Start the car and turn the wheel to both extremes to test the repair.
If the horn sounds continuously, then the washers you put in are two thick causing the air bag module to rest on the screw heads.

10. Turn the car off and reinsert the two 10 A air bag fuses, then restart the car and make sure the air bag light comes on briefly then goes off.

Hope you find this helpful.

Aug 31, 2010 | 2000 Chrysler Cirrus

2 Answers

Will 2001 zx9r fairings fit the 1998 zx9r????


will fairings from a kawasaki zx9r 98 fit on a zx9r 97??????

Apr 14, 2010 | 1998 kawasaki ZX-9R Ninja

1 Answer

Horn note adjustment on 95 lincoln town car?


you don't you have 2 horns - 1 high note, one low note. maybe one is not working.

Horn Mounting Location The horns (13832) are mounted as follows:
  • On Town Car, the horns are mounted to the horn mounting bracket (13830) that is attached to the LH side of the radiator support (16138)

Mar 15, 2009 | 1995 Lincoln Town Car

1 Answer

Where is the horn? Is there more than one?


R you seriously asking where the horns r located? That can be solved in ten sconds. Open the hood, bend over and put your head sideways just above the radiater and have a friend push the horn on the steering wheel. As unpleasant as this will be, it's a fair punishment for asking that question without at least looking down in front of the radiater first before you post.

Nov 26, 2008 | 1984 Mercedes-Benz Mercedes Benz 300 Class

Not finding what you are looking for?
1996 kawasaki ZX-9R Ninja Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...