Question about 1972 Honda CB 100

1 Answer

How do i get the headlight bulb out - 1972 Honda CB 100

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try Dratv.com, they are great with older honda's



Glenn

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change headlight on 2000 galant


  • 1
    Place the Mitsubishi on a flat service in park. Set the parking brake before continuing.

  • 2Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.


    3

    Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.


    4

    Grab the bulb and pull it from the socket with a slight wiggling motion.


    5

    Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.


    6

    Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.


    7

    Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.


    8

    Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed.


    9Close the Galant's hood.


    Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe

    Sep 27, 2012 | 2000 Mitsubishi Galant

    1 Answer

    How do you replace the headlight on a 2002 Daewoo Lanos


    Hi there, together with providing you the solution to the problem, I also took the liberty of going one step further in giving you steps on how to remove the headlight bulb.

    • Find the hood release handle and activate it, the hood should pop open.
    • Once the hood is popped open locate the hood secondary or safety latch and release it. Then finish opening the hood.
    • Locate and remove mounting clips for any plastic shields that cover the headlight lens mounting screws or clips.
    • Some headlight bulbs can be replaced by simply grasping the bulb socket behind the headlight lens and turn it counter clockwise to remove it. This will expose the headlight bulb.
    • If the headlight bulb socket is not accessible the headlight lens may need to be remove or obstructions behind the bulb removed to gain access to the headlight bulb socket.
    • To remove the headlight lens remove all mounting screws and clips that hold the headlight lens in place.
    • After the headlight housing has been removed from it's mounts, release the headlight bulb from the headlight lens housing (turn counter clockwise) the bulb will then come out of the headlight assembly. Once removed, visually verify that the replacement bulb is exactly the same as the failed bulb before to ensure a proper repair.
    • Clean the headlight lens free from all debris to help maintain the seal from the bulb to the lens. This will keep moisture out of the lens.
    • Install the new headlight bulb by turning the retainer ring or bulb clockwise.
    • Re-install the headlight lens housing and reinstall electrical connector.
    • Re-install plastic covers.
    After the job is complete turn the ignition key to the "on" position and activate the headlight switch. Observe the newly replaced headlight bulb to ensure proper operation.

    Glad to be of help!!!

    Jan 21, 2011 | 2002 Daewoo Lanos

    1 Answer

    Once I remove the nuts and bolts, I can't get the headlight to move


    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Disconnect the negative (-) battery terminal.
    3. Loosen the mounting bolts and nut of headlight assembly (A).
      22140_sant_g0056.gif

      Loosen the mounting bolts and nut of headlight assembly (A)-Santa Fe
      Click to Enlarge 22140_sant_g0057.gif

      Loosen the mounting bolts and nut of headlight assembly-Veracruz
      Click to Enlarge

    4. Take care that retaining clip (A) is not to be damaged-Santa Fe.
      22140_sant_g0058.gif

      Take care that retaining clip (A) is not to be damaged-Santa Fe

    5. Disconnect the headlight electrical connectors.
    6. Remove the headlight assembly.
    7. Remove the headlight bulb:
      • Remove the headlight bulb(s) with a counterclockwise turn-Santa Fe.
      • Remove the headlight bulb after removing the bulb caps (A)-Veracruz.
        22140_sant_g0060.gif

        Remove the head lamp bulb(s) with a counterclockwise turn-Santa Fe
        22140_sant_g0059.gif

        Remove the headlight bulb after removing the bulb caps (A)-Veracruz

    To install:

    1. Install the headlight bulbs.
    2. Install the headlight bulb caps-Veracruz.
    3. Connect the headlight electrical connector.
    4. Install the headlight assembly.
    5. Connect the negative (-) battery terminashinehutt_36.gif

    once bolts out lift up on the headlight unit hope this helps plz vote comment reply if you need more help

    Jan 17, 2011 | 2007 Hyundai Santa Fe Limited

    1 Answer

    How to install a headlight


    Locate the headlight bulb in the engine compartment, in the rear of the headlight assembly. It has a wiring harness connector attached to it.

    Remove the wiring harness connector from the bulb. Release the locking tab on the connector and pull it off the bulb. Lay it aside

    Locate the locking ring on the back of the headlight assembly. Turn the lock ring 1/8 of a turn counterclockwise to release the lock from the headlight assembly. Remove the lock ring and set it in a safe place.Remove the headlight bulb from the headlight assembly, pulling it straight back toward the engine. Discard the old bulb, unless you are reusing the bulbs in the Jeep.Insert a new bulb into the headlight assembly. (Be careful not to touch the glass when handling the bulb. The oils from your hands can cause it to overheat and shatter.)Install the headlight lock ring onto the headlight assembly and turn it clockwise 1/8 of a turn to lock the bulb into the assembly. Connect the wiring harness connector to the new bulb, ensuring that it seats completely on the bulb.Move to the opposite headlight and repeat the process to replace the second bulb. Turn on the lights to verify they are working correctly.

    Jan 13, 2011 | 1993 Jeep Cherokee Country

    1 Answer

    How do I remove halogen low beam head light to replace it?


    Removal & Installation To Remove:
    WARNING
    The halogen fog light bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
    NOTE: The headlight bulb should not be removed from the headlight assembly until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlight bulb performance. Contaminants may enter the headlight assembly where they can settle on the lens and reflector. Never turn on the headlights with the bulb removed.
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: Make sure that the headlight switch and the ignition switch are in the OFF position.
    2. Remove the pin-type retainers, screws and the air deflector from the radiator.
    3. Remove the three bolts and the headlight assembly.
    4. Disconnect the electrical connector.
    5. Remove the cover from the rear of the headlight assembly.
    6. If equipped with HID, release the spring tabs to remove the low beam bulb, otherwise disconnect the electrical connector and remove the bulb.
    7. Disconnect the electrical connector and remove the high beam bulb.
    HID low beam headlight bulb lin_tc_0085.gif

    Standard low beam headlight bulb lin_tc_0086.gif

    High beam headlight bulb lin_tc_0087.gif

    To Install:
    1. Place the headlight assembly in the proper position.
    2. Install the cover from the rear of the headlight assembly.
    3. Connect the electrical connector.
    4. Install the three bolts and the headlight assembly.
    5. Install the radiator air deflector.
    prev.gif next.gif

    Dec 18, 2010 | 2003 Lincoln Town Car

    1 Answer

    Need to replace headlight lens on a 1996 dodge avenger


    Usually, one has to get the entire headlight assembly to replace the lens.
    Is it cracked?
    If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

    ---
    REMOVAL & INSTALLATION

    CAUTION
    Halogen bulbs contain gas which is under
    pressure. Handling the bulbs incorrectly could cause it to shatter into flying
    glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
    before removal. Handle the bulb only by the base; avoid touching the glass
    itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

    • Turn the headlight switch OFF and allow the bulb to cool before
      changing it. Leave the switch OFF until the change is complete.
    • ALWAYS wear eye protection when changing a halogen bulb.
    • Handle the bulb only by its base. Avoid touching the glass.
    • DO NOT drop or scratch the bulb.
    • Keep dirt and moisture away from the bulb.
    • Place the used bulb in the new bulb's package and dispose of it properly.


    Cirrus, Stratus, Sebring Convertible and Breeze


    1. Open the vehicle's hood and secure it in an upright position.
    2. Disconnect the negative battery cable.
    3. Remove the 2 screws securing the headlight module to the radiator closure
      panel.
    4. Pull out the headlight module from the vehicle.





      Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
      module retaining screws
      90906p69.jpg






      Fig. 2: Pull the headlight module straight out of the front of
      the vehicle to remove the bulbs
      90906p70.jpg






      Fig. 3: Disconnect the wiring harness for the headlight bulb
      90906p74.jpg






      Fig. 4: Turn the light bulb retaining ring counterclockwise,
      and remove it from the back of the module
      90906p75.jpg






      Fig. 5: Pull the light bulb out from behind the module. Never
      touch the glass of the light bulb
      90906p76.jpg



    5. Detach the headlight electrical connector.
    6. Remove the retaining ring holding the bulb to the back of the headlight
      module.
    7. Pull the bulb from the back of the headlight module. Hold the bulb by its
      base only; try not to touch the glass itself.
      To install:

    8. Holding the bulb by the base, place it in the headlight module, then secure
      with the retaining ring.
    9. Attach the electrical connector to the bulb.
    10. Install the headlight module into the vehicle and tighten the 2 retaining
      screws.
    11. Connect the negative battery cable and check the headlight operation.


    Sebring Coupe and Avenger


    1. Open the vehicle's hood and secure it in an upright position.
    2. Disconnect the negative battery cable.
    3. Remove the sealing cover by rotating it counterclockwise.
    4. Remove the bulb attaching spring and pull out the light bulb.





      Fig. 6: Remove the headlight sealing cover(s)
      90906g28.gif






      Fig. 7: Remove the attaching spring and pull out the bulb
      90906g29.gif

      To install:

    5. Install the bulb into the headlight module.
    6. Install the bulb attaching spring.
    7. Install the sealing cover.
    8. Connect the negative battery cable and check the headlight operation.


    prev.gif next.gif

    Oct 07, 2010 | 1996 Dodge Avenger

    1 Answer

    How do you remove the headlight bulb


    1. Remove headlight unit
    2. Disconnect headlight leads
    3. Remove bulb cover
    4. Remove headlight bulb holder
    5. Remove headlight bulb
    6. Install new headlight bulb - DO NOT TOUCH THE GLASS PART OF THE BULB!
    7. Install headlight bulb holder
    8. Install bulb cover
    9. Connect headlight leads
    10. Install headlight unit

    I'm not aware of any shortcuts, nor do I believe that any steps could be changed or eliminated without re-engineering the headlight unit.

    Jun 06, 2010 | 2008 Yamaha Royal Star Venture

    1 Answer

    Need to replace headlight bulb 2007 hhr


    H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb

    3c8c3dc.jpg


    How to Replace a Headlight Bulb
    (DIY Complexity: Easy / Time: 0.9 hour)

    Parts:
    1. Headlight Bulb

    Tools:
    1. Screwdriver
    2. 1/4 in. Drive Ratchet
    3. Socket Set

    Steps:
    Step 1 Open the hood and locate the headlight assembly.
    o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
    o Tip: It is recommended that headlight bulbs are replaced in pairs.
    o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
    o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

    Step 2 Gain access to headlight bulb.
    o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

    Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

    Step 4 Turn on the headlights and check high and low beams to verify repairs.

    Hope this help (remember rated this help). Good luck.

    Mar 30, 2010 | 2008 Chevrolet Hhr

    1 Answer

    Replacing my headlight bulb in my kia amanit 2004


    1. Open the hood of your KIA Amanti and look behind the headlight that has gone out. Locate the round knob on the back of the headlight.
    2. Turn the knob counterclockwise 1/4 of a turn and gently remove it from the back of the headlight. Carefully remove the electrical cable within the headlight housing that is attached to the back of the headlight bulb.
    3. Locate the metal clip that holds the light bulb in place by pushing the clip arm straight in and sliding it down. Remove the bulb from the headlight housing.
    4. Replace the old headlight bulb with new bulb. Secure it by sliding the metal clip up to hold the bulb in place. Reattach the electrical cable and replace the round knob to the back of the headlight housing.
    5. Turn on the headlights to verify that they are in working order.

    Nov 03, 2009 | 2004 Kia Amanti

    Not finding what you are looking for?
    1972 Honda CB 100 Logo

    Related Topics:

    147 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4535 Answers

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    bazzz7071
    bazzz7071

    Level 2 Expert

    342 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...