Question about Harley Davidson FLHT Electra Glide Standard Motorcycles

1 Answer

IT WILL WORK THEN THE NEEDLE WILL GO TO ZERO ,IF I BANG ON THE FACE THE NEEDLE WILL WORK AGAIN ,MY ODOETER DOSE NOT TIC OFF MILES WHEN THE NEEDLE IS ON ZERO IT DOSE THIS ALOT

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 32 Answers

Replace the gauge. There is no repair for this. Also would recommend checking the cable/harness going into the gauge.

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WHAT TYPE OF OIL DO I PUT IN MY 1999 GMC SIERRA 6 LITER V8?


5w30 in cold months 10w30 in warm to hot months. High milage if its over 75,000 miles.

Apr 20, 2014 | GMC Cars & Trucks

1 Answer

I put gas in my 2000 gmc yukon and the gas gauge stopped working


when you turn the ignition on dose the needle move ? even just a bit should jump. if don't jump it may be the gauge its self not working.. if you model has the display type I.E miles left of fuel check that on the display should say how meany mile of fuel you have left to drive with.

Feb 01, 2014 | 2000 GMC Yukon XL

1 Answer

Gas gauge dose not work reading low fuel and 0 fuel miles to go


The way the MILES TO GO works is by reading how much fuel you have left. Since the FLOAT in your Tank has gone bad, it shows ZERO.

Changing the FLOAT will make the system work, but you need to have a reading to get an Estimation of fuel remaining.

Change the FLOAT and you get it working again...

Apr 16, 2013 | 2007 Saturn Aura XR Sedan

1 Answer

2004 BMW Rockster tach & speedo needles dropped to zero today.


remove the side cover and seat check for wires been crumpled this,s the problem

Jun 27, 2012 | 2004 BMW R 1150 R Rockster

1 Answer

Oil gauge on 91 Dodge Dakota suddenly running very high but plenty of oil


have a mechanic test the oil pressure with a mechanical gauge
it is more than likely that the electric sender unit has failed and is sticking internally
the tic noise could be a relay working from an intermittent power supply or bad ground

Mar 27, 2017 | 1991 Dodge Dakota

1 Answer

How do I set a imperial hvac guage


Are you trying to zero the gage? They have 3 types of calibration setups, so it will depend on the one you have. Be sure there is no pressure in the line, purge any lines or open the hand valves. Remove the plastic cover (should screw off by hand). Now some have a very small screw built in to the stop post, this post is a rest for the needle. if it has a slot turn this screw to set the needle at zero. Next is a slot on the center of the needle hand itself, look close and you will see a small center pin and a slot on ether side of that center. Use a small screw driver hold the needle hand and carefully turn the center one way or the other to re-zero the needle (may take a few trys). Next is a calibration screw built into the face of the gage (this is the easiest to do) turn it to zero your gage. Hope this Helps Fixya up.

Apr 25, 2011 | Heating & Cooling

1 Answer

Speedometer quit working. 80,000 miles needle


Your speedometer is fully electric and the sensor at the transmission side is not sending pulse to the computer ECU.

The part is call Vehicle Speed Sensor (VSS).

There are two versions.

16 bolts and 17 bolts transmission pan version.


Count the number of bolts on your transmission pan before you head for the part store.


Please rate my answer if it's useful to you.

Thanks

MUSTGO.

Dec 11, 2009 | 2003 GMC Sierra 1500

1 Answer

Tic tic problems


check filtering capacitor of lot+B & replace it

May 14, 2009 | LG Studioworks 700S 17" CRT Monitor

3 Answers

HONDA S2000 STARTER PROBLEM


sounds like a bad starter selnoid or starter drive

Feb 18, 2009 | 2002 Honda S2000

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4345 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...