Question about 2001 Harley Davidson FLHRCI Road King Classic

1 Answer

Can you bypass the axillary light and just have the main headlamp

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Sure you can if you don't mind doing a few wiring changes. By "axillary light", I'm assuming you are talking about a light bar on the front of the bike with spot lights on either side. Usually most guys have these lights wired so that they can turn the on and off independently of the headlight and the ignition switch for that matter. But, I guess some people want to run them all the time so they wire them directly to the headlight wiring. I don't have a schematic on that bike so you'll just have to trace the wires out.

Good Luck
Steve

Posted on Sep 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of the headlight relay.


Has no headlight relay ! your headlamps not working ? high or low ? You have a headlamp switch an a dimmer switch for low or high beams ! The main light switch should have battery + voltage all the time .You can go to http://bbbind.com/free_tsb.html free wiring diagrams ! Shows fuse's , connectors an wires at main light switch an dimmer switch ! Suggest you go on youtube an watch a few videos on electrical circuit testing an how to read a wiring diagram ! Pull the main light switch out of the dash an test for B+ voltage an test at the dimmer switch too. Test the whole circuit !

Aug 14, 2016 | 1995 Ford Taurus

1 Answer

What could be causing the front axillary fuse to keep blowing? Even bigger fuses blow.


fuses blow from over current( dead short) they are rated at lower than what is required so that the wire doesn't burn
If you keep putting in bigger fuses without fixing the dead short, eventually the wire will melt the plastic insulation off and the vehicle will burn

Apr 29, 2016 | 2005 Buick Rendezvous

1 Answer

2000. Where is fuse for tail lights?


Do your headlamps work ?
Park/Marker/License/Tail Lamps
Voltage is applied to the turn/headlamp switch at all times. When the turn/headlamp switch is in the PARK or the HEAD position, voltage is applied to the following components:
?€¢
The park lamps


?€¢
The marker lamps


?€¢
The tail lamps


?€¢
The license lamp

The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
The automatic lamp control function turns on the park lamps and the headlamps. This action occurs when the ambient light sensor determines that the exterior lamps should be turned ON based on the amount of available light. When the BCM grounds the park lamp relay, voltage is supplied directly to the park lamps, bypassing the turn/headlamp switch assembly. When this action occurs, the following conditions exist:
?€¢
The automatic lamp control relay is grounded.


?€¢
The headlamps turn ON. Refer to Headlights/Daytime Running Lights (DRL) Circuit Description .

The lamps turn OFF when the BCM does not ground the park lamp relay or the automatic lamp control relay. This action is caused by the following conditions:
?€¢
The available light reaches a predetermined level.


?€¢
The ignition switch is turned to the OFF position

Mar 31, 2016 | Pontiac Grand Am Cars & Trucks

1 Answer

Adjust headlight on harley ultra classic


Hi Larry, the correct procedure for adjusting a head light is as follows:
1. Verify correct tire inflation.
2. Place motorcycle on a level floor or pavement in an area with minimal light.
3. Point the front of the motorcycle towards a screen or wall witch is 25 feet from the axle of the front wheel.
4. Draw a horizontal line that is exactly the same height above the floor as the floor is to the center of the head light.
5. Have a person whose weight is roughly the same as that of the principal rider sit on the motorcycle seat. The weight of the rider will compress the suspension slightly.
6. Stand the motorcycle upright with both tires resting on the floor and with the front wheel held in straight alignment pointing forward.
7. Turn the Ignition/Light Key Switch to Ignition. Set the Light Switch on the left handlebar to High Beam.
8. Check the light beam for proper height alignment. The center of the main beam of light should be even with the horizontal line on the screen or wall.
9. Check the light beam for proper lateral alignment. The main beam of light should directed straight ahead i.e. equal area of light to the right and left of center.
10. The headlamp adjustment can be performed without removing the chrome ring. If the headlamp alignment requires adjustment use slots in the headlamp chrome ring to insert phillips screw driver between headlamp housing and rubber gasket. Turn the vertical adjustment screw as necessary to align the headlamp vertically. Turn the horizontal adjustment screw to adjust the headlamp horizontally. Good luck.

Aug 08, 2012 | 2009 Harley Davidson FLHTCU Ultra Classic...

1 Answer

Adjusting the headlight on 2005 roadking


Hi Anonymous, the correct procedure for adjusting a head light is as follows:
1. Verify correct tire inflation.
2. Place motorcycle on a level floor or pavement in an area with minimal light.
3. Point the front of the motorcycle towards a screen or wall witch is 25 feet from the axle of the front wheel.
4. Draw a horizontal line that is exactly the same height above the floor as the floor is to the center of the head light.
5. Have a person whose weight is roughly the same as that of the principal rider sit on the motorcycle seat. The weight of the rider will compress the suspension slightly.
6. Stand the motorcycle upright with both tires resting on the floor and with the front wheel held in straight alignment pointing forward.
7. Turn the Ignition/Light Key Switch to Ignition. Set the Light Switch on the left handlebar to High Beam.
8. Check the light beam for proper height alignment. The center of the main beam of light should be even with the horizontal line on the screen or wall.
9. Check the light beam for proper lateral alignment. The main beam of light should directed straight ahead i.e. equal area of light to the right and left of center.
10. The headlamp adjustment can be performed without removing the chrome ring. If the headlamp alignment requires adjustment use slots in the headlamp chrome ring to insert phillips screw driver between headlamp housing and rubber gasket. Turn the vertical adjustment screw as necessary to align the headlamp vertically. Turn the horizontal adjustment screw to adjust the headlamp horizontally. Good luck.

Jul 24, 2012 | 2005 Harley Davidson FLHRCI Road King...

1 Answer

How do you adjust the headlight on my harley xr1200


Hi Schnauzersru, the correct procedure for adjusting a head light is as follows:
1. Verify correct tire inflation.
2. Place motorcycle on a level floor or pavement in an area with minimal light.
3. Point the front of the motorcycle towards a screen or wall witch is 25 feet from the axle of the front wheel.
4. Draw a horizontal line that is exactly the same height above the floor as the floor is to the center of the head light.
5. Have a person whose weight is roughly the same as that of the principal rider sit on the motorcycle seat. The weight of the rider will compress the suspension slightly.
6. Stand the motorcycle upright with both tires resting on the floor and with the front wheel held in straight alignment pointing forward.
7. Turn the Ignition/Light Key Switch to Ignition. Set the Light Switch on the left handlebar to High Beam.
8. Check the light beam for proper height alignment. The center of the main beam of light should be even with the horizontal line on the screen or wall.
9. Check the light beam for proper lateral alignment. The main beam of light should directed straight ahead i.e. equal area of light to the right and left of center.
10. The headlamp adjustment can be performed without removing the chrome ring. If the headlamp alignment requires adjustment use slots in the headlamp chrome ring to insert phillips screw driver between headlamp housing and rubber gasket. Turn the vertical adjustment screw as necessary to align the headlamp vertically. Turn the horizontal adjustment screw to adjust the headlamp horizontally. Good luck.

Aug 20, 2011 | Harley Davidson XR1200 Motorcycles

1 Answer

98 ford lariat. Headlights stopped working. running lights come on and brake lights and turn signals. checked all fuses under dash and under hood, pulled out headlight switch and it looks fine. note only...


Is this both the high beams and low beams that do not work ?

If you checked all 3 fuses with a meter ( with the headlamp in Low position for both low beam fuses or in high for the high beam fuse ), the next items to test are the MFS ( MultiFunction Switch ) and the main headlamp switch ( test not look at it ).

The main headlamp test chart
568bbbb.jpg

The test chart for the MFS
4fc6f66.jpg
097ea29.jpg

Oct 25, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Day time running lamps


The day time running lamps are your headlights, the parking lights also conventionally known as the running lights serve no purpose during daylight hours and as such are not necessary in the daytime, and are not illuminated by the DRL module. The DRL (Daytime Running Lights) module illuminates the headlamps in a slightly dimmer state than night time dim headlamps, but does not turn on the conventional running lights. The only way you'll get conventional running lights during the day is to turn them on manually. I just reviewed the wiring schematics for that system, and the DRL relay bypasses the dimmer switch when active and prevents high beam operation, and feeds current directly to the low beam headlights, there is no connection to the parking light circuit from the DRL module wiring.

Nov 01, 2008 | 2000 GMC Sierra

Not finding what you are looking for?
2001 Harley Davidson FLHRCI Road King Classic Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...