Question about 1979 Harley Davidson XLS 1000

1 Answer

Left turn signal light will not illuminate and balb is not burned out it is a wiring problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

You should have a grey wire with a violet band on it going to the turn signal socket. Make sure you have a good ground on the turn signal unit.

Good Luck
steve

Posted on Sep 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left turn signal and stop light pin for trailer has power


Recheck the wiring on the truck and trailer.

Mar 31, 2016 | Cars & Trucks

2 Answers

2007 hd ultra glide auxillary fuse keeps blowing


Hi Anonymous, you have a dead short which is usually the easiest to find. Using a test light connected to the hot side of the blown fuse holder, start probing the wire leaving the fuse holder about an inch away the test light should illuminate, keep probing towards the ignition switch until the test light no longer illuminates you are now very close to the short. For more information about your issue, please visit the websites below, and for specific information or questions, please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
Harley Davidson Wiring Diagrams and Schematics
Harley Davidson Manuals Mark Workshop

Nov 16, 2012 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Front left running light burns too bright and left rear blinker blinks faster.


Hi Kevin, you have the front left turn signal bulb installed 180 degrees out or your wiring is bass ackwards. Good luck and have nice day.

Mar 10, 2012 | 2008 Harley Davidson FLSTC Heritage...

2 Answers

Left blinker flash fast, hit brake left blinker goes out left taillight goes out but both backup lights come on


Usually a fast flashing signal is because one of the bulbs is burned out or shorted out. If the signal and brakes use the same light which many cars do then check the wiring to it and replace bulb. If burns out again then it has a short between the signal switch and the actual light or the brake wiring to it is shorted.

Sep 03, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

1986 HD sportster 883 bought without turn signals. Located two wires on both forks and two single wires to rear signals. How do I wire led's? Tried and all 4 lights illuminate with either turn signal and...


Your bike came with front running lights (black wire) and turn signals. The wire color for the turn signals are gray wires. The grey turn signal wires have small rubber bands on them to indicate which side they are for. A brown tag indicates right turn signals and a violet tag indicates left turn signals. If you need a schematic, I have one but I cannot send it via this forum. This forum only allows for a 150Kb picture and the schematic is larger than that. I'll be glad to scan the schematic and send it to you if you'll contact me directly at wd4ity@bellsouth.net Remind me that you need a schematic for a 1986 Sporty.

Good Luck
Steve

Aug 31, 2010 | 1993 Harley Davidson XLH Sportster 883

2 Answers

How do I fix my left blinker? light still works but it sticks instead of blinks


What you speak of as to the left blinker doesn't flash, yet the instrument cluster shows the green arrow (to the left), and yet that and the left turn signal lights do not flash, appears to be a simple burned out bulb. If one of your left turn signal bulbs are burnt out, then the #552 Flasher Unit in your fuse box is NOT the cause. It's the "Amperage" not being correct to the flasher unit. Place the parking brake on and start your vehicle. Put the left turn signal on and check to see ALL the bulbs are illuminated for the left turn signal. If you find one bulb that is not illuminated, then replace the bulb. It should be an 1157 bulb, but in the front it could be a 1157 Amber bulb dependent on whether your turn signal lens is clear or yellow.

If you still have difficulty finding the dead bulb, turn on the right turn signal and see which bulbs are illuminated and this will give you an idea as to which bulb on the left side isn't working, or turn on your Emergency Flashers which will turn on both the left and right side lamps and see which bulb is not lit up.

I hope this Helps,

~00 Buck~

"Still living on the Right Side of Dirt..."

May 24, 2010 | 1972 Oldsmobile 98

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
1979 Harley Davidson XLS 1000 Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...