Question about kawasaki ZXR 750 Motorcycles

1 Answer

HI CAN YOU GIVE ME THE PART NO FOR THE CAM CHAIN GUIDE RUBBER IN THE TOP OF THE CAM COVER FOR A 1994 ZXR750 L2

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Cam chain guide PN# 12053-1286

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Kia Optima with a 2.4L engine The engine started to knock when driving home. When I pulled over the noise was only apparent at the top of timing cover on the intake side.


yes this engine uses a hydraulic variable cam guide , it moves via oil pressure as engine moves faster ive seen this a few times that the actuator for this develops a oil leak (oil drains back down to pan not outside) and it no longer maintains a proper tension in cam drive chain , I suggest you have this further investigated to see if this is what has occurred , as it can develop into a very serious problem if let go too long , also your mention that there is slack in cam chain isn't a good sign either

Jan 06, 2017 | 2007 Kia Optima

1 Answer

How easy is it to fit a cam chain and link in sit to a Honda CB 750 1994. and what is the main problem with a rattling chain on one? is it mainly the chain for the cam, or the lower drive chain for the...


eaasy take off the timing /rocker cover and the top chain guide exposing the top of the chain undoo locknut and back off tensioner then break chain after tying both ends with cord so they cant fall in then splice the new chain onto the old and wind it through taking care to not let it jump teeth on timing wheels, detatch old chain from the new one, swage rivet pin in join of new chain crank engine by hand with a spanner two full rotations to check for valve piston interference and reassemble tighten tensioner until chain feels tight then back off 1/4 turn put back upper chain guide and bolt down rocker cover and you are done easy

Oct 21, 2014 | Motorcycles

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

Need diagram how to install timing chain 2004 Malibu overhead cam


Procedure is pasted below. Please let me know if you have questions.
Removal & Installation2.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    NOTE The timing chain has 2 matching colored links and 1 uniquely colored link.
    Negative battery cable, PCV hose, Fuel line bracket, Ignition coil and module assembly Ground strap from camshaft cover, Camshaft cover, Front fender liner, Accessory drive belt Crankshaft balancer pulley, Accessory drive belt tensioner, Front cover-to-water pump bolt Remaining front cover bolts, Front cover
  5. Rotate the engine until the crankshaft sprocket mark aligns with the matching colored link (2) at the 5 o-clock position.
  6. Confirm that the INT diamond on the intake camshaft sprocket is aligned with the uniquely colored link at (1) the 2 o-clock position.
  7. Confirm that the EXH triangle on the exhaust camshaft sprocket is aligned with the matching colored link (3).
  8. Remove or disconnect the following:
    NOTE Use a 24 mm wrench to hold the camshafts to prevent them from turning.
    Timing chain tensioner, Fixed timing chain guide access plug, Fixed timing chain guide Upper timing chain guide, Exhaust camshaft sprocket, Timing chain tensioner guide Intake camshaft sprocket, Timing chain through the top of the cylinder head Crankshaft sprocket

    jturcotte_638.jpg

    Fig. Lining up the crankshaft sprocket mark with the colored link in the 5 o-clock position (2).


    jturcotte_639.jpg

    Fig. Aligning the intake camshaft sprocket mark with the colored link in the 2 o-clock position (1).


    jturcotte_640.jpg

    Fig. Aligning the exhaust camshaft sprocket (3).

To install:
  1. Install the crankshaft sprocket with the timing mark in the 5 o-clock position.
  2. Assemble the intake camshaft sprocket to the timing chain with the timing mark lined up with the uniquely colored link (1). Hand tighten a new intake camshaft sprocket bolt.
  3. Lower the timing chain through the opening in the cylinder head.
  4. Route the timing chain around the crankshaft sprocket and line up the first marching colored link (2) with the timing mark on the crankshaft sprocket.
  5. Install the exhaust camshaft sprocket with a new bolt loosely onto the exhaust camshaft.
  6. Align the timing mark on the sprocket with the last matching colored (3).
  7. If necessary, align the camshaft as follows:
    1. Using a 24 mm wrench, first turn the intake camshaft until the alignment feature on the back of the camshaft sprocket seats in the notch in the front of the intake camshaft.
    2. Turn the crankshaft 45 degrees in either direction.
    3. Turn the intake camshaft to the appropriate location.
    4. Turn the crankshaft back to top dead center (TDC).
  8. When the sprocket seats in on the camshaft, tighten the sprocket bolt hand tight.
  9. Verify all of the colored links and the appropriate timing marks are still aligned.
  10. Install the fixed timing chain guide. Tighten the bolts to 133 inch lbs. (15 Nm).
  11. Install the upper timing chain guide. Tighten the bolts to 89 inch lbs. (10 Nm).
  12. Using a 24 mm wrench to hold the camshafts, tighten the camshaft sprocket bolts 63 ft. lbs. (85 Nm) plus 30 degrees.
  13. Measure the timing chain tensioner from end to end. A new tensioner should be supplied in the fully compressed non-active state. A tensioner in the compressed state will measure 2.83 inches (72 mm) front end to end. A tensioner in the active state will measure 3.35 inches (85 mm) from end to end.
  14. If the timing chain tensioner is not in the compressed state, perform the following steps:
    1. Remove the piston assembly from the body of the timing chain tensioner by pulling it out.
    2. Install the bottom half of the Tensioner tool J-45027-2 into a vise.
    3. Install the notch end of the piston assembly into the bottom half of the tensioner tool.
    4. Using the top half of the Tensioner tool J-45027-1, turn the ratchet cylinder into the piston.
    5. Install the compressed piston assembly back into the timing chain tensioner body until it stops at the bottom of the bore. Do not compress the piston assembly against the bottom of the bore.

  15. Install the timing chain tensioner assembly. Tighten to 66 ft. lbs. (75 Nm).
  16. Release the timing chain tensioner by compressing it approximately 0.08 inches (2mm). Feed a rubber-tipped tool down through the cam drive chest to reset on the cam chain. Give the tool a sharp jolt diagonally downwards to release the tensioner.
  17. Install the timing chain oiling nozzle.
  18. Install the timing chain guide bolt access hold plug with silicone sealant on the threads. Tighten the plug to 59 ft. lbs. (90 Nm).
  19. Install or connect the following:

    Camshaft cover. Tighten the bolts to 89 inch lbs. (10 Nm). Front cover with new gasket. Tighten the bolts to 18 ft. lbs. (25 Nm). Accessory drive belt tensioner. Tighten the bolts to 33 ft. lbs. (45 Nm). Crankshaft balancer pulley using a new bolt. Tighten the bolt to 74 ft. lbs. (100 Nm) plus 75 degrees. Accessory drive belt, Front fender liner, Ground strap to camshaft cover Ignition coil and module assembly, Fuel line bracket, Air intake assembly, Negative battery cable
  20. Refill the cooling system to the correct level.
  21. Refill the engine with oil to the correct level.
  22. Start the engine and check for leaks.

    jturcotte_2381.gif

    Fig. Compressing the timing chain tensioner-2.2L engine.

Oct 06, 2011 | 2004 Chevrolet Malibu

1 Answer

How do i take the oil tank off a 41 cc husky chain saw


I guess we are talking about the Husqvarna 41/141, start by removing the guide bar and chain, remove top cover, disconnect and remove the throttle wire, remove the fuel hose from the carb, use a 4mm allen key and remove the front anti vibration rubber screw ( drive side, bottom front r/h, holding the alloy chain catcher ) now remove the top anti vibration rubber screw with a cross head screw driver ( top l/h holding an orange plate ) now remove the four screws securing the starter cover, two screws are into the plastic crankcase, and two are into the anti vibration rubbers, the fuel tank should now pull out from the bottom of the saw withe top handle still connected, make sure the fuel hose feeds out of the crankcase as you pull the tank away.

Feb 10, 2011 | Garden

2 Answers

1999 VULCAN HAS OIL LEAKING AROUND THE SPARK PLUG DOWN A WEEP HOLE AND OUT THE BACK OF THE CYLINDER HEAD. WHAT IS CAUSING BUILD UP OF OIL IN THE SPARK PLUG WELL? REAR CYLINDER RIGHT SIDE PLUG


hi, sounds like the oil seal in the rocker cover has failed, remove the rocker cover and you will see a rubber seal, this seals the oil inside the cover, however when the seal fails around the spark plug hole, oil leaks into spark plug well and out of weep hole.

Jan 24, 2011 | kawasaki VN 1500 Vulcan Classic Tourer...

1 Answer

Head gasket got bent and I have replaced it . Now the problem I'm facing is how to set the crank shaft and the comshaft timing. I need the procedure for engine timing


Timing Chain & Gears Removal & Installation To Remove:
NOTE: Keep the cam chain away from magnetic fields.
Crankshaft set at TDC marks hnda_trk_crv_crank_tdc_marks.gif

  1. Turn the crankshaft pulley so its Top Dead Center (TDC) mark (1) lines up with the pointer (2).
  2. Raise and support the vehicle.
  3. Remove the front tires/wheels. Front undercar splash shield hnda_trk_crv_frt_under_splsh_shld.gif

  4. Remove the front undercar splash shield.
  5. Remove the drive belt.
  6. Remove the cylinder head cover (See section on Valve Cover).
  7. Remove the crankshaft pulley (See section on Crankshaft Damper). CKP sensor and VTC solenoid electrical connectors hnda_trk_crv_ckp_vtc_ele_conn.gif

  8. Disconnect the Crankshaft Position (CKP) sensor connector (1) and Variable Valve Timing Control (VTC) oil control solenoid valve connector (2).
  9. Remove the VTC oil control solenoid valve (See section on VTC Solenoid Valve).
  10. Support the engine with a jack and wood block under the oil pan. Ground cable and upper bracket removal hnda_trk_crv_grnd_cbl_uppr_brckt_rem.gif

  11. Remove the ground cable (1), and remove the upper bracket (2). Side engine mount bracket removal hnda_trk_crv_side_eng_mount_brckt_rem.gif

  12. Remove the side engine mount bracket. Timing chain cover removal hnda_trk_crv_timng_chain_cov_rem.gif

  13. Remove the timing chain cover bolts both from the front to the block and from the bottom to the oil pan.
  14. Remove the timing chain cover.
  15. Loosely install the crankshaft pulley. Compress the timing chain auto-tensioner hnda_trk_crv_compr_tim_chain_auto_tensnr.gif

  16. Turn the crankshaft counterclockwise to compress the auto-tensioner. Lock the timing chain auto-tensioner hnda_trk_crv_lock_tim_chain_auto_tensnr.gif

  17. Align the holes on the lock (1) and the auto tensioner (2), and then insert a 0.06 inch (1.5 mm) diameter pin (3) into the holes.
  18. Turn the crankshaft clockwise to secure the pin. Removal of the timing chain auto-tensioner hnda_trk_crv_rem_tim_chain_auto_tensnr.gif

  19. Remove the auto-tensioner. Removal of the timing chain guide B hnda_trk_crv_rem_tim_chain_guide.gif

  20. Remove the cam chain guide B. Removal of the timing chain guide A hnda_trk_crv_rem_tim_chain_guidea.gif

  21. Remove the cam chain guide A (1) and tensioner arm (2).
  22. Remove the cam chain.
prev.gif next.gif

Oct 11, 2010 | 2002 Honda CR-V

2 Answers

Does the 2000 silverado v8 have a timing chain and if so at what milage should it be replaced


yes the silverado's have timing chains, just about all v6's and v8's have timing chains, and timing chains should not be serviced, unless you are having problems with a timing chain guide or timing chain tensioner

Aug 08, 2010 | 2000 Chevrolet Silverado

1 Answer

How to re-shim zxr750 j1


take the valve cover off make sure the the cylinder that you are workin on is at top dead center compressionor the nose of the cam facing up.. you will have to get the shim specs from the manuel... make sure when you shim, that you shim it to the middle of the spec range

Aug 18, 2009 | 1990 kawasaki ZXR 750

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77194 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...