Question about 1999 Suzuki TL 1000 R

1 Answer

Hi,i have put a 2002 engine and loom into my mates 1998 frame it runs ok,on the left hand side bottom of the rad whats the elec plug for,also on the bottom of the fuel tank main feed to injection plug type also two other metal pipes one seems to be a return where does the other one go to,help please,regards nick.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 192 Answers

The plug on the radiator is a sensor usually for overheating or temperature purposes. There should also be a vent tube coming off of your tank. That might be what the other tube is for. Hope this helps.

Posted on Sep 09, 2010

Testimonial: "ok thanks"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is engine oil drain plug on 2002 harley softail standard

Hi Anonymous, it is on the bottom of the frame tube right hand side all the way in the rear. Have nice day.

Feb 15, 2013 | 2004 Harley Davidson FXST - FXSTI Softail...

5 Answers

Changng antifreeze on a kia sedona

there is no drain plug you will have to take the hose off the bottom to drain it then turn the engine over for just a few seconds then turn it off , this will pump out any other fluid

Oct 26, 2008 | 2002 Kia Sedona

1 Answer

Where is the oil drain plug for 2002 road king

There are three oils. You do not say which one.

Dyna engine oil is on the left side bottom of the oil pan near where the jiffy stand rests when up and straight in from the side. The primary is under the middle of the primary case on the left side facing the ground and the transmission is under the right side of the oil sump case about mid way from front to back. All are 1/4 inch ALLEN socket heads inside 5/8 inch hex plugs. All use an o-ring and thread sealant.

Softail is the same except the engine oil drain is on the right side at the rear of the frame down tube near the swing arm attachment point and faces the ground.

Touring is the same except that the engine oil drain plug is on the left hand side front of the oil pan facing the front.

Sportster engine oil drain is on a rubber tube hanging down under the frame near where the jiffy stand rests when in its up position and the transmission and the primary use the same drain plug and are the same oil. The engine oil plug is a 5/16 inch plastic plug held in place with a mini worm screw clamp with a plain screwdriver or ¼ inch hex worm drive fitting.

Sep 28, 2012 | 2002 Harley Davidson FLHRCI Road King...

1 Answer


there should be an engine number and frame number on your bike which will identify your bike. the engine no is usualy stamped on the bottom engine casing (usualy left hand side). the frame no. should be on the frame just behind the forks. the numbers should both be present and should be the same, not sure how to use this number but take this to your local bike mechanic and he should be able to help you. i had to do this when my mate bought a ty175, wich turned out to be a 1980 dt175!!

Jan 10, 2012 | Yamaha YZ 426 F Motorcycles

1 Answer

Coolingfan doesn't stop , it keeps on running, tell me what to do

the themostat switch has shorted out or there is a short in the wiring loom you can stop the fan by pulling the plug out that feeds it its 12 volt supply you will find the plug close to the fan motor by the rad,,however you still need to change the thermostat switch in the water jaket,,, the bike will be ok to drive so long as you dont sit in traffic or let it stand ticking over you need to be driving it at a speed of at least 20 mph so that air go's through the rad to cool the motor down or you will cook the engine up?

Jul 14, 2010 | 2002 BMW K 1200 LT

1 Answer

How to replace freeze plugs in 1998 ford explorer with 4.0 engine. Center freeze plug on driver side came out with rust around it. whats the process of repair?

make sure there is no material from the old plug left in the hole. clean inside hole with light grade emory cloth. put some hi-temp sealer on the mating surface of the plug. tap into place hollwed side out, edge flush with the engine surface. measure the hole precisely to get the correct size plug. access to hole may be limited.

Feb 25, 2010 | 1998 Ford Explorer

1 Answer

Bmw 328 coupe number plate light only one works but if i change the units to the side that works both work but the right side don't work whats wrong! on the right side i tested the power and it rads 1.1 on...

It sure sounds like there is a break in the circuit to the right hand bulb. See if you can follow the actual wire back to where it goes into the loom. Possibly a push fit plug loose or out.

Oct 06, 2009 | 1999 BMW 318 ti

1 Answer


i guess you are asking how to install it
here is how it works
first of all dont buy cheap glad you bought this
here are the steps

Disconnect positive battery terminal.

Drain engine coolant.

Remove engine mounts (2) from van frame and flip them over backwards.

Remove the hood latch (leave cable connected)

Remove the two bars that connects the frame to the inside fender.

Remove the engine coolant overflow tank

remove air filter cover and filter and accordian hose

Remove upper and lower rad hoses

remove the two brackets that holds the rad

remove the two bolts that holds the fan assembly to the rad (one each end)

unplug fan plug

unhook lines from bracket at bottom of fan assembly.

remove fan assembly.

remove bolts from ac lines to condenser.

remove bracket that holds ac lines to rad (I think it's the rad)
lift rad upwards and away from frame enough to lift condenser out.

hope it helps-

Aug 17, 2009 | 2002 Chevrolet Venture Passanger

1 Answer

Water leak from radiator bottom right hand corner or pipe in area

Please the radiator has been damaged. Ensure you change it before it turns your engine off totally leading to engine change.

Be careful next time.

Good luck.

rate this fixya!

Apr 07, 2009 | 1998 Volkswagen Golf

1 Answer

Replacing the radiator system for nissan altima 1998

Drain coolant from the cooling system. White plastic drain plug in bottom of radiator.

take off bottom rad. hose and top rad hose.

All wrenches and sockets are either 10 or 12 mm. Remove air shroud from around radiator and fan.
Sometimes its easier to remove fan too.

If its an automatic, remove 2 rubber hoses at bottom of rad.

remove 4 bolts top and bottom that hold rad. in place.

reverse order of parts. Fill with coolant and check for leaks.

That is the basics of it.

Sep 26, 2008 | 1998 Nissan Altima

Not finding what you are looking for?
1999 Suzuki TL 1000 R Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides