Question about 1981 Honda GL 1100 Innerstate Gold Wing

1 Answer

Starter runs but does not turn the moter - 1981 Honda GL 1100 Innerstate Gold Wing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

There is a one way clutch that grabs onto a smooth cylinder on the side of a large gear inside the motor. The smooth barrel surface is on the side of what Honda calls the "starting sprocket". A chain connects the starting sprocket to a smaller sprocket that has the starter spline plugged into it. To replace this you will have to unbolt the motor and at least rotate it far enough to remove the rear cover. The chattered surface does not allow the three small barrels of the starter clutch to grab and turn the motor over. The sprocket runs about $70 and the gasket runs about $38.

Posted on Sep 09, 2010

Testimonial: "I was almost sure i would have to pull back cover, needed some reinforsement! i thought it would be starter clutch, not gear, thanks"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter motor solenoid wont engage


There is condenser shaped part attched to the starter moter this is the part which makes the starter moter to spin and when it is stuck the moter does not spin you can check it by one person sitting in the car holding the key to start position and another one hit it softly with some spanner or something The starter moter will move there is a small gear in it which requires replace ment Or the other possible reason can be the carbon brushes in the starter moter are worn out or the place where these brushes touch on armature the place is worn out that Y ou will only come to know when you will take the moter away from the engine Lastly I hope you might have checked your battery that it is giving sufficient current to the moter

Aug 16, 2012 | 2003 Volkswagen Jetta TDI

1 Answer

Starter moter wont stop running 1988 harley 1200sportster


your starter plunger is sticking you can take it apart and lube it or drill a small hole in the side case big enough to get a skinny screw driver trough lube through that hole and work the plunger back and forth make shure you dissconnect battery first

Feb 14, 2012 | Maisto Harley Davidson 1997 XLH Sportster...

1 Answer

How do u wire a three phase squirrel cage motor with a motor starter with a remote start/stop/inch station and warning indicator light ?


You would first run a conductor fromL1 to L1 on the motor start then run a second conductor from L2 to L2 on the moter starter, then run a third conductor from L3 to L3 on the moter starter. next run L1 and L2 to a step down transformer so you can reduce your working voltage to 120vac, then run a conductor on one of the outputs from the step down transformer to one side of the normally closed contacts on the STOP push button, from the other side of the stop button run a wire to one side of the start button, on the other side of the start push button run a wire to one side of the magnetic motor starter coil, the other side of the coil run a wire to the other empty terminal on the transformer, this will be the neutral wire. next you need to run a wire from the normally open contactor on the magnetic moter starter to one side of your push button start switch, then run one wire from the other side of the start push button switch to the other side of the normally open contacts on the magnetic moter starter, this is your start switch latch that will keep the motor running when the start push button is released.I'm not sure how you need the warning indicator light wired up, so please reply and let me know when it needs to come on and go off

Feb 04, 2010 | Delta TP300 Shopmaster 12-Inch Portable...

1 Answer

My 1995 mazda 626 4 cyl wont start. its getting gas spark. when you turn the moter over you hear like a muffeled noise at the moter not muffler


Your problem could be a lot of things ,,without hearing the noise we have to gess your problems like
1Chech the engine for turning over if not then its the starter bendix slipping and if it is turning over as usual then its could be the starter ring on the flywheel and if so turn key off and turn engine over by hand about 1/2 way around on bottom pully and try starting again and if it starts then its the starter ring.
Engine or Gearbox out job.
Let me know how you get on . Ron

Nov 11, 2009 | 1995 Mazda 626

1 Answer

2000 ford focus no power to starter moter i can run wire from ignitionswitch and ground starter and turn key and starter runs but wnenstarter is put back in car switch will not turn starter over i...


The mechanic should check on the wires and fuse going to the starter motor and the spare parts . since when you test the starter motor and seems no problem to it ,it means that the problem is in the other spare parts connected to the starter motor .check the alternator if it is good and functioning well. The solenoid you also have to check it to be sure because it is very much connected to the starter motor .those spare parts that are worn out or destroyed , you should replace them .

Aug 28, 2009 | 2000 Ford Focus

1 Answer

The engine wouldn't turn over.


check the battary make shore theres plenty of life in it , if that doesent work make shore the starter moter is not jamming, if the stater moter is jamming try to krank it over mannualy that will free the starter moter , and then it should turn over . if it does then your starter motor is the problem

Jun 22, 2009 | 2004 Dodge Durango

2 Answers

Starter motor


It sounds like your starter moter needs new brushes and servercing it sounds like it is not spinning over quick enough to fire the motor over fast enough.Get a firm in your local area that do every thing to do with starter moter alternators .Have a look in your local yellow pages

Nov 10, 2008 | 2004 Aprilia RST 1000 Futura

1 Answer

Dryer motor will not turn


You have teeth that are not connecting in the moter just like a starter moter on a car..Take moter out and find a motor rewind shop in the yellow pages they will either repair the motor or offer you a part exchange..hope this helps

Jan 01, 2008 | Dryers

Not finding what you are looking for?
1981 Honda GL 1100 Innerstate Gold Wing Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...