Question about 2001 Harley Davidson XL 1200 C Sportster Custom

1 Answer

Trying to find out out to hook up a relay switch for a Wolo Model 400 horn on my Harley.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Try writing Wolo an e-mail and request a wiring schematic.

Good Luck

Posted on Sep 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove the horn

Hi, Michael first check for continuity at the power and ground wire at the horn, then check for continuity at the horn button, back in the day there was a small adjustment screw on the back of the horn, by turning it one way or the other you could set the limit on how much the diaphragm vibrated. For more information about your issue, please visit the websites below, and for specific information or questions, please feel free to contact me at Good luck and have nice a day. Mini Beast Air Horn Installation
Wolo Bad Boy Air Horn Installation
Harley Davidson Manuals Mark Workshop
Owner Manuals Harley Davidson USA

Jan 06, 2016 | 2008 Harley Davidson FLHTCU Ultra Classic...

1 Answer

How do i install wolo horn on jeep with two factory horns?

If you are trying to make it work simultaneously with stock horns, I suggest you wire it in through a relay. Without a relay you will be placing too much of a load on the horn circuit.
A relay is typically used to control a component that draws high amperage. The relay allows full power to the component without needing a switch that can carry the amps. The switch only controls the relay. The relay then provides a direct connection to the battery. It should be noted that either the power(86) or ground(85) in the relay control circuit can be switched. In the case of a horn, the horn button would be used to switch the ground lead(85) and power(86) would be provided directly from the fuse box.
This is a typical wiring diagram for a standard relay installed for headlights, horn, fuel pump, electric fan, etc. If the relay has a 5th terminal, it is not used.


Aug 30, 2014 | Wolo Wolo Manufacturing BADBOY419 Model...

2 Answers

Horn does not work; where is the horn?? in a 2002 2500HD 4X4? Many thanks.\r\nBob ibGorham Maine

There's two of them located just above the parking light in front of each of the fender wells. You will be able to see them from the bottom looking up

Jun 26, 2011 | 2002 Chevrolet Silverado 2500HD

1 Answer

How to install wolo air horn #519 2004 ultra

Hi Benjamin, for more information about your question please visit the websites below. Good luck and have nice day.
Wolo Bad Boy Air Horn Installation

Jun 22, 2011 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to install a wolo air horn #519 on 2004 harley ultra

Hi Benjamin, please be aware that this question has already been asked and answered. Thank you.

Jun 22, 2011 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to install #519 wolo horn on 2004 harley ultra

Hi Benjamin, please review the previous question and answer. Thank you.

Jun 22, 2011 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I installed a wolo air horn 419 and when I push the horn button all I here is the compressor and no horn.

It is possible that you may have reversed the polarity on the compressor; it may be "pulling" air instead of blowing it out. Remove the air hose from the compressor and put your thumb over the air outlet while pressing on the horn switch. If you don't feel air blowing out, reverse the positive & negative wires going into the compressor and repeat the test. The air horns should work at this time.

Note: Always install a relay on this type of horn system; the compressor puts a high amount of load on the horn switch if you don't.

Apr 09, 2011 | Honda CB 900 Hornet Motorcycles

1 Answer

I recently bought a 130 Db WOLO horn and button/wire kit. The horn is to be used as an additional horn to my factory one. I thought it might be a good idea to buy a relay as well for safety purposes but I...

Hi, a horn needs only 4 blades.

Please see my tip at . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Apr 02, 2011 | Chevrolet TrailBlazer Cars & Trucks

Not finding what you are looking for?
2001 Harley Davidson XL 1200 C Sportster Custom Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

4339 Answers


Level 3 Expert

76070 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides