Question about 2000 Yamaha YZF-R6

2 Answers

Hello had a motorcycle accident. He collided with the stone fence. motorcycle speed was not significant. the garage will tell you that he not be kept as body rolls. It can be or not?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Yamaha Master
  • 4,521 Answers

What??

Posted on Sep 07, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Trust the garage. I am sure the forks are bent and chances are the frame is twisted as well. The cost to repair the bike will be more than the bike is worth.

Posted on Sep 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can this saw be adjusted if it cuts out of square? And if so, how.


Hello, yes this saw can be adjusted.
To calibrate the table, use a framing square up against the rear fence and see how the blade tracks. To adjust this: loosen the bolts holding the rear fence down and move the fence until it is square with the blade track and tighten.
To adjust the bevel: use a speed square to check for 90deg and 45deg on the blade. Using the 13mm bolts found at the pivot point on the trunnion you can adjust the 90 and 45 degree angles.

Mar 12, 2016 | Hitachi 8.5"" Sliding Compound Miter Saw...

1 Answer

Under the burnt out green of this small yard's tufts of grass where water was once used to wash pots , pans, poes,ochre appaers. a rusted bucket , hole kicked into its bottom, lies on its side. fence , lo...


It sounds like a good summer project. That yard might take some work. The first thing you will want to do is clear out the wildlife (including neighbors) and rebuild the fence. I suggest digging a trench and have the fence go a foot or two into the ground to prevent the animals from coming back underground. After that, the bushes will need to pulled out and grass can be planted. I wish you luck!

Elisa Jed ' http://www.qualitychainlinkfencing.ca/services.html

Mar 04, 2014 | Computers & Internet

1 Answer

My 2005 nissan altima was involved in an accident. I kept the car in the garage for a couple of months . Today I took the car out the garage with any problem when I tried to drive out of the driveway the...


most likely cause is a siezed up piston in the brake caliper but again i wouldnt like to answer with a good look at the vehicle myself to confirm my suspicions

Jul 30, 2011 | 2005 Nissan Altima

1 Answer

How do you make a 2006 Expedition headlight adjustment?


You will need to know the height and width adjustment first from a manual like a haynes manual from your local autozone store $20.00. Then it will tell you how to put some tape and measurements on the garage door or fence ect... so you can aim them.

Nov 16, 2010 | 2003 Ford Expedition

1 Answer

Need parts for husky tile saw THD750l need bolt fence


Hi, Take a look at amazon for replacement parts: Amazon com Husky tile saw. Hope this was helpful. cheers

Sep 30, 2010 | Husky Wet Tile/Stone Saw with with Laser...

1 Answer

I have a ´06 Vthunder, when going on 4th or 5th gear and try to recover speed the clutch seem to be engage, you can hear how the RPM goes up, but no speed change, by the way, no adjustment left on the...


hello. it seems that the clutch is starting to wear significantly. the best you can do is make sure that there is freeplay left in the clutch lever. but if no more can be had then it is obvious that the clutch plates need to be inspected, for they are most likely worn and/or damaged beyond service limit. this will show more likely in the higher gears.

Mar 24, 2009 | 2006 Vento V Thunder XL

6 Answers

Max speed


mine did 76mph and i used Shell V-power but i weight 12stone so if your less then it will make a differance

Nov 10, 2008 | 2008 Yamaha YZF-R125

Not finding what you are looking for?
2000 Yamaha YZF-R6 Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...