Question about Honda CR 125 R Motorcycles

1 Answer

Free complete clutch and linkage diagrams - CR 125 R Honda Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Go to the following website. Please rate my answer. Thanks.
www.babbittsonline.com/pages/parts/viewbybrand/default.aspx

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i ajust my clutch


To work efficiently, the clutch needs the right amount of play in the linkage between the foot pedal and the clutch operating lever (also known as the release arm or fork).
Anything less than the correct amount o free play (or clearance) will result in clutch slip, because the pressure plate will be unable to exert its full pressure on the friction plate.
Failure to cure this fault will quickly lead to a burned-out friction plate, and possibly a ruined pressure plate.
If, however, there is too much clearance in the clutch linkage, the car tends to creep forwards when in gear with the clutch pedal fully depressed.
This is known as clutch drag, and it can cause difficulties in heavy traffic.
It is generally better, however to have too much play in the clutch linkage than too little. Adjusting the clutch

Oct 10, 2017 | Cars & Trucks

1 Answer

I installed a complete clutch & Flywheel. I popped outta 1st gear & won't go into any gear whatsoever. Linkage & slave cylinder work! feels like it's going into gear but when i let clutch out nothing


Isolate the problem. Sound like clutch is stuck and not disengaging. Engine off put in gear and rock the vehicle,, with help from a friend press clutch pedal while in gear and have friend push, you will know if the tranny is ok and clutch is stuck. Now check the clutch, slave etc for engagment and disengagment / Clutch linkage- movement/travel may need adjustment or you have something wrong in the reassembly..

Feb 08, 2016 | Cars & Trucks

1 Answer

Need Diagram of linkage for 2002 PT Cruiser under the hood


There is no "linkage" under the hood. It is a hydraulic clutch, and the only linkage is form the pedal to the clutch master cylinder, which is bolted directly to the firewall. So all the physical "linkage" is inside the passenger compartment.

Here is a picture of the master cylinder:
25941431-ks0rn1mjxp3kpgoxvtvly4ea-2-0.jpg
You can see the bolts that come thru the firewall..

If you are having issues with the clutch, I recommend replacement like the dealer recommends: the complete sealed system. You can get it at Autozone via special order. It comes completely assembled, including Master and Slave cylinders and reservoir. Here is a picture of that:




25941431-ks0rn1mjxp3kpgoxvtvly4ea-2-1.jpg

Nov 04, 2015 | 2002 Chrysler PT Cruiser

1 Answer

I need a diagram for clutch linkage for 1966 chevy impala


Its pretty simple set up, you go from the pedal assembly to the rod in the back down to the frame rocker, the linkage from the frame rocker to the clutch fork, you will also have a return spring there

Jan 08, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

I need a diagram for a 2005 peterbilt clutch linkage


a clutch linkage for what type of tranny ? fuller ? Road ranger? 10 , 13 18 speed? semi auto? probably different tannys might have different linkage set up no?

Jun 30, 2014 | Garden

1 Answer

Diagram gear linkage citroen relay


use engine oil from a oil can ,wd40 is no good for this ,if gears hard to get then check the gearbox level (EP90) also is the clutch clearing ok ,later models use a plastic carrier support for the thrust bearing and these melt causing the clutch not to clear properly making the gears hard to change

Jan 31, 2013 | Peugeot 505 Cars & Trucks

2 Answers

Cna i adjust athe clutch in a 1994 toyota pick-up


The linkage cable before the trans should have an adjustment nut on it. This controls the fork assembly movement. adjust the linkage to remove the pedal free play and this will also tighten the clutch.

Jun 04, 2010 | 1994 Toyota Pickup

1 Answer

The clutch won't disenguage


If your clutch won't release properly, it will continue to turn the input shaft. This can cause grinding, or completely prevent your car from going into gear. Some common reasons a clutch may stick are:
  • Broken or stretched clutch cable - The cable needs the right amount of tension to push and pull effectively.
  • Leaky or defective slave and/or master clutch cylinders - Leaks keep the cylinders from building the necessary amount of pressure.
  • Air in the hydraulic line - Air affects the hydraulics by taking up space the fluid needs to build pressure.
  • Misadjusted linkage - When your foot hits the pedal, the linkage transmits the wrong amount of force.
  • Mismatched clutch components - Not all aftermarket parts work with your clutch.

Mar 21, 2010 | Oregon Scientific Electric PTO Clutch for...

1 Answer

Need diagram for clutch clutch fork zbar and linkage for 69 nova big block


Try obsolete chevy parts,on line.You can order parts,I believe they will have the diagram also.Brace on bell housing,bushing,axle,bushing,brace on frame.

Dec 12, 2009 | Chevrolet Nova Cars & Trucks

2 Answers

I have a Kenworth T-2000 and the clutch pedal stuck down and hard to push


Sounds like your Clutch has failed.

you can also unhook the linkage at the clutch arm on the trans and make sure the linkage is free

Oct 04, 2009 | Denso Nippondenso RS232

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers

yadayada
yadayada

Level 3 Expert

79186 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...