Question about kawasaki KLR 650 Motorcycles

Open Question

2001 kawasaki 3010 mule not getting fuel,was running fine, stopped like it ran out of gas,no fuel pumping thur fuel line

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: Kawasaki Mule 3010, keeps getting flat battery, wont jump start

Sometimes when the battery keeps going dead like that, a component may be creating a current draw. you can do a simple current draw test with a fluke meter by setting the meter to read amps, make sure the test leads are in the proper portals on the fluke for an amp test, and disconnect one of the battery cables and connect the test leads in-line with the battery and cable. It would help to know you have a good fuse inside the fluke. They are easy to blow, and whatever you do, DO NOT try to start the unit with the meter hooked up for the amp draw test. That is how fuses are blown. With the key off, check for any amp draw. If there is, you can start unplugging components until the draw goes away. If there was no draw to begin with, you may have a stator coil (or alternantor, whichever it has) that is weak and can't keep up.

Posted on Jun 11, 2009

  • 2 Answers

SOURCE: 1999 kawasaki mule will not

the problem might be a cdi box or stater or might be a rectifire/regulator

Posted on Jun 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

Why do I keep having to replace the fuel pump?


Check your fuel filter! Fuel not being filtered properly is the main cause of fuel pump failure.

May 26, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

Info for Mule 610


sounds like electric fuel pump when it quits,take fuel line off at carb turn key on you should hear pump and see fuel coming at line

Sep 21, 2014 | kawasaki 2013 Mule 610 4x4

1 Answer

What is possible cause that a mule 3010 kaf620e6f will not hold idle?


Air leak .dirty air filter.,.fouled plug.,.bad gas.,.dirty carb?fuel injection? Bad fuel filter ,fuel pump test fuel pump that's the general stuff.go from there

Apr 28, 2014 | kawasaki 2006 Mule 3010 4x4

2 Answers

#1cylinder not firing on 2003 3010 Kawasaki mule


if its firing ok on other cylinders, unlikely to be pump or fuel filter, focus on electrics, plug, ht lead etc

Dec 08, 2013 | 2003-2007 Kawasaki Kaf620 Mule 3010 4x4...

1 Answer

Kawasaki Mule 1999 Model


Hello Anon..
First, I would check to make sure the carbs are getting fuel, and then fuel getting into the cylinders. Your question about low oil - did you let it get low and then it quit? ...
If you put oil into the cylinders and only got 100psi, this might be your problem. You should be pumping around 120+psi without putting anything into the cylinders... Recheck the compression.= .take out all spark plugs...screw the gauge in until the o-ring seats, hold the throttle wide open while spinning the engine over for about 5 seconds... you should get 120psi +/- 10psi.
If you are getting less than 100psi.. it might be time for a rebuild..

May 24, 2017 | kawasaki 2005 Mule 3010 Trans 4x4

1 Answer

Why does my Kawasaki mule 3010 stall and then won't start for about 10 minutes


Have your fuel pump checked. The wires on mine were melting due to the regulator attached the pump being bad so when the mule would first start it would run fine until it warmed up and then no gas once the wires warmed up. Don't buy the Kawasaki replacement unless you want to pay $300 or more for the part (They are crazy over-priced on parts) and labor. Got a 3rd party pump for $50 and had it replaced for one hours labor and we are good to go. Worse case next time around I buy another $50 pump and replace it myself

Aug 14, 2012 | kawasaki Motorcycles

1 Answer

I have a 2008 kawasaki mule 3010 and i dont have any power to my fuel pump, if i put power to the pump it work and i can drive it where and what wires do i need to check? a wiring schematic would be nice.


Hi Dragracing19, I am sorry you can't find the first and best tool you ever bought for your Mule but despair not for a mere $15.00 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
2008 Kawasaki ATV Service Repair Workshop Manuals

Jun 30, 2011 | kawasaki W 2 (SS Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...