Question about Harley Davidson XL 883 Sportster Motorcycles

1 Answer

Just need to know how tight to tighten specs on rocker arm

Posted by on

  • Anonymous Mar 15, 2014

    needtorque specs. for 1977 xlh rocker arm shaft end nut

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

I assume you're working on an Evolution or a Twin Cam and you're talking about the torque specs on the lower plate.

5/16" bolts 15-18 foot pounds
1/4" bolts 10-13 foot pounds

Hope this helps
steve

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs 2003 olds silhouette rocker arm 3.400


Here is a suggested updated torque spec for this engine's rocker arm bolts;
Rocker arms
Step one: Torque to 11 ft lbs then tighten an additional 90 degrees of bolt head rotation. Some guys don't fuss with the torque specs and just get them good and tight. Either way, be careful, as the heads are aluminum. You do not want to over tighten these bolts

Oct 07, 2016 | 2003 Oldsmobile Silhouette

1 Answer

Torque specs 2003 kia sedonna rocker arm


Tighten the bearing cap in two or three steps. Tighten it to the standard torque at the last stage. *Bearing cap standard torque Torque16 pieces at the both ends : 18.6 - 20.6 N·m(190 - 210kg·cm, 13.7 - 15.2 lb·ft)24

Jun 16, 2014 | 2003 Kia Sedona

1 Answer

Rocker arm specs


ROCKER ARM SUPPORT PLATE
Installing the rocker arms and rotating the engine with the valve
train loaded can result in bent push rods, damaged bushings
or a warped support plate.

To install the rocker arm support plate, both lifters of the
cylinder being serviced must be on the base circle (or
lowest position) of the cam.
Place the rocker arm support plate assembly into the rocker housing. Loosely install the four
rocker arm support plate bolts with flat washers.
Tighten the rocker arm support plate bolts in a cross pattern and alternately tighten
each of the four rocker arm support plate bolts just 1/4 turn. THEN continue turning the bolts in these increments until snug. THEN following the same sequence, tighten the bolts to 18-
22 ft-lbs (24.4-29.8 Nm).

THEN install and alternately tighten the two bolts to secure breather assembly to 90-120 in-lbs (10.2-13.6 Nm).

May 12, 2014 | 2008 Harley Davidson FXD Dyna Super Glide

1 Answer

2003 ford taurse 3.0 ohv rocker arm torque specs


To install, reverse the removal procedure. Tighten the rocker arm bolts in two stages.
  • Stage 1: Tighten to 10 Nm (89 lb-in).
  • Stage 2: Tighten to 32 Nm (24 lb-ft).

Jun 26, 2011 | Ford Taurus Cars & Trucks

1 Answer

I HAVE A 93 GM 350 TBI K MOTOR. I NEED THE TORQUE SPECS FOR THE ROCKER ARM NUTS.


I dont know the excact specs but i have been instructed to tighten untill zero lash and then tighten 1/2 to one full turn more ...i have built about 7-10 350s and this has always worked for me

May 25, 2011 | 1993 Chevrolet G20

1 Answer

I need to know the torque specs for the head gasket for a 99 2.2 pontiac sunfire


Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)


Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).


Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Apr 05, 2011 | 1999 Pontiac Sunfire

2 Answers

Rocker arm toruge specs, how many lbs?


FOR THE 242 -4.0 ENGINE ROCKER ARM TORQUE IS 21 FT LBS FOR THE 5.2L AND 5.9L ENGINES ROCKER ARM TORQUE IS 21 FT LBS.

Aug 04, 2010 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...