Question about 2004 Honda CRF 150 F

1 Answer

What are the choke positions - 2004 Honda CRF 150 F

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 127 Answers

All the way down is choke on,all the way up is choke off..

Posted on Sep 12, 2010

  • alex ulber Oct 05, 2010

    Actually yz-maniac is wrong, i have a 2004 crf150f and all the way down is choke off, in the middle is half choke, and all te way up is full choke, hope this helps.

  • Danny
    Danny Oct 06, 2010

    My bad, you are right coolbeans27. my son has a 2005 crf150f and i just went outside and verified it backwards...sorry.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to start a ryobi200blower blower 200

First , prime the priming bulb about 4 x...

Next put the choke lever in full choke position

Give a couple slow pulls, then a good strong pull...

(The unit should burp, run for a second)

Next put the choke lever in the half choke position

Pull rope

It should start and run, now put the choke lever all the way in the off position and let unit warm up a minute... if when you turn choke off it stalls out, u didn't warm it up enough...

Oct 10, 2015 | Garden

1 Answer

How do I start a weedeater fb25?

Press primer bulb 6 times
Move throttle lever to start position
Move choke lever to full choke position
Pull starter rope sharply until engine attempts to start, but no more than 5 pulls.
Move choke lever to half choke position. Pull starter rope sharply engine runs. If engine hasn't started after 5 pulls, repeat all steps above.
After warming up for 10 seconds, move choke lever to run position. has a manual for this model available for free download

Oct 20, 2014 | Weedeater Garden

1 Answer

Ingine stops after started in choked position on stihl weed trimer

Try leaving it on choke or half-choke until it warms up ( a few minutes)...then move the choke to the RUN position.

Aug 13, 2010 | Yard Machines Garden

1 Answer

My chainsaw will start but it boggs down and shuts down when I pull the trigger to rev the engine..

Could be not getting enough fuel. Check pick up tubing and filter in tank. Or could b the choke is not opening. You didn't mention what brand but some saws have a spring that returns the choke to the open position. If its not in place, then even with the choke lever in the open position the choke is not. Remove cover and observe the position to the choke plate. If the saw has been sitting, then a good carb cleaning is in order.

Jun 30, 2010 | Garden

1 Answer

Trimmer will only run in choke position

You have a few possibilities. Make sure you have good fresh gas in the tank. You're not getting enough gas, so choking helps get more gas than air, making it run better. Could be the carb diaphram (not very expensive if you replace yourself), when they get old they don't perform like they should. Could be the filter in the gas tank is bad, plugged. Also might be just an easy adjustment on the carb Low, and High speed screws. The choke has three positions, full choke, partial choke, and no choke, which means run position.

Apr 28, 2010 | Homelite Consumer Products 4.0 Amp, 13 In....

2 Answers

What is the choke on position on a '03 dr z125

What is the choke position on a superbyke rcc 125

Nov 15, 2009 | 2003 Suzuki DR-Z 125

1 Answer


(---) is choke on

( I ) is choke off.

This symbol represents the butterfly valve in the carburetor. When it's straight up, the butterfly valve is not restricting the air flow, therefore, it is not choking. Vice versa for the other symbol.


Aug 31, 2009 | Garden

1 Answer

Stalling out

Generally with two cycle engine as soon as the engine starts the choke needs to be moved to the off or open position. Some chokes have a middle position that lets the motor run until it is warm enough to move the choke into the open position. In other words weather it is a two or four cycle engine the choke is used only to start the engine. If you unit is newer and still does not run well with the choke in the open position, you may need to adjust the hi-speed circuit to a richer one.

Jul 13, 2009 | Troy Bilt Tb70ss Gas Trimmer

1 Answer

Choke wont stay in the closed position for starting

Been a while since I saw a Jonsered but I think if you bend the choke linkage a little that it will stay in the choke position.

May 19, 2009 | Standard Oregon Chainsaw Chain For...

1 Answer

Forgot which position switches should be and choke on/off position

choke on when starting one pull or two choke off when running. line up/ down is full choke , slant line is no choke.

Apr 22, 2009 | Garden

Not finding what you are looking for?
2004 Honda CRF 150 F Logo

Related Topics:

932 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides