Question about 1985 Yamaha XJ 700 X Maxim

1 Answer

Whenever I shift (at a stop) from neutral to first the whole bike either shifts/jolts or occasionally grinds the gears. The clutch is fully depressed when doing so. Thoughts on how to fix or what is happening?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Your idle may be set too high . 800 to 1000 RPM should be about right. That can cause problems shifting from a stopped position.You may have the wrong oil in your cycle . Do not use car oil or any oil that says Energy Conserving on the label . It will shorten the life of your wet clutch and transmission gears. Use oil that has the JASO MA certification on the label. 10w-40 cold climate or 20w-50 hot climate. A synthetic oil will help you run cooler and shift easier in hot weather conditions and under all conditions. One other thing to check is your clutch plates , if the bike sat for a number of years, the clutch plates could be stuck together. Take off the clutch cover , take off the springs, take off the clutch pressure plate, and pull all the plates out. Carefully separate the plates, replace any scored or burnt plates , rub oil on all the surfaces, and put them back in. This will make the clutch work smoothly if the plates were causing the problems.

Posted on Sep 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission not shifting completely


Sounds like you don't have enough clutch clearance. The clutch is dragging the gears. Not sure on your bike as you don't mention what you have, but in some bikes I had there was a manual clearance adjustment on the centre of the clutch. Once that is set, the play of the cable was adjusted. Of course hydraulic actuation might differ.

Aug 06, 2015 | Motorcycles

1 Answer

Slips from Drive to neutral at 35 mph.


Check the fluid and its level. If fluid smells burnt then clutches inside are slipping if fluid is red and smells ok then you will need someone to diagnose it, possibly a shift solenoid not engaging the 3-4 shift.

May 31, 2015 | 1997 Ford F150 Regular Cab

1 Answer

I need 2,3 & 4 gear for Yamaha 1100 special 1982 model


Instructions
    • 1 The gears on a motorcycle run in this order: first, neutral, second, third, fourth and fifth. When you are moving, shifting up from first gear will skip over neutral and shift you right into second gear. The only time that shifting up from first will get you into neutral is when you are not moving.
    • 2 Pull in the clutch lever and tap the gear lever down until it stops. This will signify first gear. Pressing the gear lever down will shift you down one step and pressing it up will shift up one step.
    • 3 Tap the gear lever up one click while still holding in the clutch. This will put the bike into neutral.
    • 4 Start the bike. The bike needs to be in neutral to start.
    • 5 Hold in the clutch lever and tap the shifting lever down to shift to first gear.
    • 6 Release the clutch slowly and give it just enough gas to get moving.
    • 7 Listen to the motor to know when you need to shift. If the engine is making a low grumbling noise, then it will need to be shifted down. If it is making a high squealing noise, then it needs to be shifted up.

Jan 15, 2013 | Motorcycles

1 Answer

Where can I find 2/3 & 4th gears for Yamaha XJ special 1982 model.


Instructions

1

The gears on a motorcycle run in this order: first, neutral, second, third, fourth and fifth. When you are moving, shifting up from first gear will skip over neutral and shift you right into second gear. The only time that shifting up from first will get you into neutral is when you are not moving.
2

Pull in the clutch lever and tap the gear lever down until it stops. This will signify first gear. Pressing the gear lever down will shift you down one step and pressing it up will shift up one step.

3

Tap the gear lever up one click while still holding in the clutch. This will put the bike into neutral.
4

Start the bike. The bike needs to be in neutral to start.
5

Hold in the clutch lever and tap the shifting lever down to shift to first gear.
6

Release the clutch slowly and give it just enough gas to get moving.
7

Listen to the motor to know when you need to shift. If the engine is making a low grumbling noise, then it will need to be shifted down. If it is making a high squealing noise, then it needs to be shifted up.

Jan 15, 2013 | Motorcycles

1 Answer

HOW TO SHIFT TO 4 WHEEL DRIVE


Hi - Here is instruction how to do.

From N to 4H

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H".

From 4H to 4H LOCK

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H LOCK".

If the vehicle is moving, we recommend

that the speed be less than 100 km/h (60

mph) during this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H LOCK to 4L LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4L LOCK".

From 4L LOCK to 4H LOCK

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to shift into "4H LOCK".

From 4H LOCK to 4H

You can operate the transfer switch either

when the vehicle is stopped or while the

vehicle is moving.

Position the front wheels straight ahead

and turn the switch to shift into "4H". If the

vehicle is moving, we recommend that the

speed be less than 100 km/h (60 mph) during

this operation.

NOTE:

• When shifting between the transfer

switch position and the transfer gear

position is unmatched, all 4WD indicators

will blink and the buzzer will sound.

• If it is difficult to shift between "4H" and

"4H LOCK" while the vehicle is moving,

try accelerating and decelerating your

vehicle several times after turning the

transfer switch. Be sure to wait until traffic

conditions allow you to accelerate and

decelerate safety before using this procedure.

From 4H to N

64J209

Stop the vehicle completely, place the

transmission in "N" (Neutral) and depress

the brake pedal and the clutch pedal fully

(if equipped), then push in and turn the

switch to the mark (1) at the left of the "N"
position, and hold the switch in this posi-

tion for 5 seconds until the "N" indicator

blinks, then turn the switch to the "N" position.

When you turn the transfer switch to the

"N" position, "N" indicator will come on with

the buzzer sound.

CAUTION

• Be sure to stop the vehicle completely

before operating the transfer

switch to shift between "N" and

"4H", or between "4H LOCK" and

"4L LOCK".

• Do not shift between "4H" and "4H

LOCK" unless the front wheels are

in the straight-ahead position and

we recommend that the vehicle

speed be less than 100 km/h (60

mph).

Do not operate the transfer switch

while tires are racing.

• Do not operate your vehicle in "4H

LOCK" or "4L LOCK" on dry, hard

surfaces.

(Continued)

CAUTION

(Continued)

• Do not operate the vehicle while a

4WD mode indicator is blinking

except when shifting between "4H"

and "4L LOCK".

If you operate the vehicle while a

4WD mode indicator is blinking, a

buzzer will sound and the transfer

will shift to "N" (Neutral) to prevent

transfer case damage.

In this case, use the following procedure.

1) Depress the clutch pedal fully (if

equipped) or shift the automatic

transmission gearshift lever to the

"N" position.

2) Turn the transfer switch to the

position previously selected.
3) Operate the transfer switch again.

Feb 01, 2011 | 2007 Suzuki Grand Vitara 4WD

1 Answer

Gear shifting


Adust clutch cable.Test...start the car in first gear with clutch fully depressed, parking break off. Slowly release the clutch. determine when the vehicle starts to move. If clutch is fully depressed call that 100%, fully released is 0%. The vehicle should be moving at around the 55-45% range.

Dec 02, 2009 | 2002 Nissan Xterra

1 Answer

Grinding Noise When Clutch Is Depressed, Lights Flicker


you may need to have your clutch cable adjusted ... it is most likely not releasing the clutch fully and grinding against the flywheel

Oct 06, 2009 | 1998 Volkswagen Jetta

2 Answers

1997 Yamaha FZR 600 cuts out when shift into first gear


Does the bike have a sidestand switch that cuts the power if the stand is left down? If it does, disconnect it and temporarily join the ends together and try starting....

Mar 20, 2009 | 1994 Yamaha FZR 600

4 Answers

Transmission shifting proublem M5R1 1997 FORD RANGER


internal slave cylinders are known to leak , unfortunate it is behind clutch assembly , i would change both , clutch master and slave cylinder

Feb 27, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Grinding and very hard to shift, and now the shifter is stuck


how does the clutch pedal feel?..clutch out of adjustment,needs clutch job...kev-mn.

Dec 10, 2008 | 1995 Pontiac Sunfire

Not finding what you are looking for?
1985 Yamaha XJ 700 X Maxim Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...